The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 27, 2007, 09:04 PM   #1
Liquor
Junior Member
 
Join Date: March 16, 2007
Posts: 7
Noob: Lee Anniversary Kit

Hi;

I'm a noobie to relaoding, I just got a Lee Anniversary kit with the challenger press for my B-day. Anyone use this setup and any setup/tweak tips to make sure it's setup properly? I'll be reloading 7mm rem Mag for now.

Thanks,
Liquor
Liquor is offline  
Old April 27, 2007, 10:18 PM   #2
Randy_che
Member
 
Join Date: July 28, 2005
Location: Houston, Texas
Posts: 56
OK, here's a tip. Make a little box out of cardboard to put inside the existing "primer catch box". An ammo box or cereal box works well for the cardboard. It will be taller on the right side than the left. Work with the shape until it is a good fit and it catches well. When you get it right, it catches almost all the primers and is much easier to empty.

If your ball handle comes off, drill a small hole through the top of the ball for a vent, then use JB weld to glue the ball back on. If you don't drill the hole, it will be very hard to get the ball on there because you will be making an air compressor piston.

That was 2 tips.
Randy_che is offline  
Old April 28, 2007, 08:24 AM   #3
MakarovFan
Member
 
Join Date: June 21, 2006
Location: Eastern Ohio
Posts: 87
I recently got the same press kit as a second setup since I can't find shell holders anymore for my old press.

I like the idea by Randy che, I will have to do that myself.
I have been just using the shop vac in my workshop, that was going to be my tip.

I would double check the weight scale from time to time, mine seems to come off zero from time to time.
MakarovFan is offline  
Old April 28, 2007, 05:54 PM   #4
KW-Bane
Senior Member
 
Join Date: October 22, 2006
Location: Mississippi
Posts: 109
Because of Lee's powder dispensor: check and weight the powder drops often...it may drop a few with more or less powder. It varies with diff powders, some more consistant than others. Flake powder has alittle more trouble being consistant than round or ball powders.

W231 is a good powder, but has a sneaky way of working itself into the mechanics of the powder dispensor making it alittle stiff.

Remember to use good safety habits!

Try to be consistant every time you reload, as to make all the ammo the same.

Start out with loading just a box of rnds (50 or so), shoot them to chk accuracy etc. This works on more than 1 level...it may help you in case you forget something and have to pull all the bullets.
__________________
http://www.kwsquad.com/kwsite2/
"Everyone knows there is right and wrong, but integrity proves a man"
KW-Bane is offline  
Old April 28, 2007, 05:57 PM   #5
CrustyFN
Senior Member
 
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,255
If the wooden ball comes off the handle I would replace it with something different.
Rusty
__________________
I don't ever remember being absent minded.
CrustyFN is offline  
Old April 29, 2007, 09:20 AM   #6
tstone
Member
 
Join Date: January 9, 2007
Location: MS
Posts: 25
Run a least a full hopper through the powder measure before using it to actually reload ammo. This coats the innerds with graphite, and seems to help with static and consistency. KW is dead on about the flake powder.
tstone is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:21 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05199 seconds with 7 queries