The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 26, 2007, 11:31 AM   #1
oldcars
Senior Member
 
Join Date: March 13, 2007
Posts: 375
45 acp bullets in 45lc case?

I just bought my first reloading setup and I also bought about 9000 .452 bullets at an estate sale, both 225g f.p. and 230g r.n. and I was wondering if I can use them in a 45 long colt case? I bought them for my 45acp but I am looking at a 45lc blackhawk, and that would be an inexpensive way to enjoy a big bore single action. I think it should work by the info in the reloading book, but I just wanted to make sure.
oldcars is offline  
Old April 26, 2007, 11:35 AM   #2
Dillonhelp
Member
 
Join Date: February 9, 2007
Location: Arizona
Posts: 40
I have successfully used the 225 fp bullets in 45 Colt. With the 230 RN projectiles, watch the overall length. I don't think it would be a problem in the older Rugers, as they were built on the Superblackhawk frame, but in some other revolvers, the bullet protrudes past the end of the cylinder.
Dillonhelp is offline  
Old April 26, 2007, 01:55 PM   #3
John in AR
Member
 
Join Date: April 17, 2007
Location: Arkansas
Posts: 16
I do that very thing. 230-grain lead flatpoints, over Titegroup in a .45LC case. Never a problem, but as Dillonhelp says, you have to watch OAL.

Watch for accuracy issues in your gun as well. A lot of .45LC guns like .454 bullets, and .45acp bullets are likely to be .451 or .452. No dangers, but accuracy could potentially be less than ideal, much like with the old .357/9mm convertible Blackhawks.
John in AR is offline  
Old April 26, 2007, 03:31 PM   #4
KW-Bane
Senior Member
 
Join Date: October 22, 2006
Location: Mississippi
Posts: 109
I started out the same way reloading .45acp's then added reloading .45colt's.

I use .452 230gr LRN and loaded W231 for both.
I fine tuned the load to make them very accurate.

Hogdon has reloading data on their website that you may find helpful. http://data.hodgdon.com/cartridge_load.asp
__________________
http://www.kwsquad.com/kwsite2/
"Everyone knows there is right and wrong, but integrity proves a man"
KW-Bane is offline  
Old April 26, 2007, 05:45 PM   #5
cheygriz
Senior Member
 
Join Date: May 11, 2002
Location: high up in the rockies
Posts: 2,232
I've probably loaded more ".45 ACP" bullets in my .45 Colt cases, than the bullets that were designed for it.

But my all time favorite plinking and informal target bullet for the .45 Colt was the old Lyman 230 grain full wadcutter. From several different guns, it cut one big ragged hole at 50 yards shooting from the bench.
__________________
If you think a mighty military force is expensive, wait 'til you see what a weak one costs.
cheygriz is offline  
Old April 28, 2007, 03:10 PM   #6
44 AMP
Staff
 
Join Date: March 11, 2006
Location: Upper US
Posts: 11,364
Before WWII

.45 Colt guns normally had .454 groove diameter. Afterwards, it became normal for guns to have .452 dia. I have Ruger Blackhawks, and have never had any trouble with ACP bullets.

Check you loading dies, mike the expander. If it is .454", you might want to use the expander from a .45 ACP set, 'specially if you are going to load above plinker level.
__________________
All else being equal (and it almost never is) bigger bullets tend to work better.
44 AMP is offline  
Old April 28, 2007, 04:19 PM   #7
shooter1
Senior Member
 
Join Date: July 30, 2005
Posts: 137
A .452 cast bullet is a .452 cast bullet. I have loaded many of the 230gr RN in .45 Colt cases. They work great. I also have some 255gr LSWC bullets I am current loading into ACP cases. This bullet over 5grs of Unique is exceptionally accurate in one of my .45s. (Safe in my guns, your mileage may vary) Just be sure you have good safe loading data from a reliable source, and load away@@
str1
shooter1 is offline  
Old April 28, 2007, 07:13 PM   #8
Johnny Guest
Moderator Emeritus
 
Join Date: August 28, 1999
Location: North Texas
Posts: 4,116
ACP bullets in .45C are fine

My first efforts in loading .45 colt, nearly 40 years ago, were an outgrowth of my ACP reloading. I bought a shell holder and used ACP dies, properly adjusted, with home cast 225 LRN bullets. I used the same charge of Unique I'd been loading with that bullet in ACP cases. It was a nice, mild plinking load for my new "western style" Colt SAA. Before long, I bought a used set of .45C dies.

In recent years, I've loaded quite a few bulk packed 230 LRN ACP bullets over around 8.0 gr of W-231 for use in my S&W .45 Colt Mountain Gun. These get around 900 fps and I shoot 'em in IDPA style matches. The smooth profile RN bullets load very nicely from HKS speedloaders.

Best
Johnny
__________________
MOLON LABE!
Amendment II ensures the rest of the Bill of Rights.

Blog: Expert Witness
Johnny Guest is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:19 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07210 seconds with 7 queries