The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 1, 2007, 11:51 AM   #1
wlw4281
Junior Member
 
Join Date: December 26, 2006
Posts: 1
Building a reloading room from scratch

I have a room I am going to build in my attic for mainly reloading. I would like to have some suggestions and pictures of ideas you guys have had success with in your own reloading space. I am looking for mainly bench designs, and storage space solutions. I use 4 presses, but will get more if the room does not break the bank. Thanks for any help you can give.
wlw4281 is offline  
Old April 1, 2007, 12:11 PM   #2
rwilson452
Senior Member
 
Join Date: June 10, 2004
Location: Tioga co. PA
Posts: 2,342
my bench

the first reloading bench I made custom used 3/4 melamine doubled. it was glued and screwed together. the screws were installed from the bottom and didn't go all the way thru. legs were 4X4 crossmembers were 2X4. to pu the top to the frame I put pieces of 2X4 flat to the melamine and screwed them on then went all the way thru the cross members in the 2X4 that was already afixed to the top. Where the press was to be put I used more 4X4 under the top and used lug bolts into it from above holding the press on. no flex in the top. when I worked the press. Storage is in cheap three shelf cabinets I picked up at wallmart. I stacked them. small parts and brass I store in recycled soft butter tubs. large and small. For smaller stuff I have used bottles my RX pills come in. Computer labels either printed or hand scribbles for lables. Ackro bins are nice of you can get them cheap. I lucked into some from a hardware store that closed it doors.
rwilson452 is offline  
Old April 1, 2007, 12:29 PM   #3
Shoney
Senior Member
 
Join Date: February 21, 2002
Location: Transplanted from Montana
Posts: 2,311
In the good old summertime, what temperatures do you expect to have in that attic? Just remember that hot temperatures are not good for powder or primer life.

I have seen lots of "Show us your loading bench." type threads in this and other forums, so do a search, you will get lots more input in less time.
__________________
I pledge allegiance to the Flag - - -, and to the Republic for which it stands….Our Forefathers were brilliant for giving us a Republic, not a democracy! Do you know the difference??? and WHY?http://www.wallbuilders.com/LIBissue...les.asp?id=111
Shoney is offline  
Old April 1, 2007, 12:48 PM   #4
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
I recently upgraded from an old steel computer desk to spanning a whole wall with a built in bench. 4X4's, 2X4's, and 3/4" plywood. It worked great but My 'puter is refusing to install Photoshop so I can't post pic's for the time being.
Edward429451 is offline  
Old April 1, 2007, 01:52 PM   #5
FM12
Senior Member
 
Join Date: February 5, 2007
Location: Monroeville, Alabama
Posts: 1,591
Just make sure the bench area where the presses are mounted is HEAVY and STURDY, i.e. NO FLEX in that part. Everything else should be designed for economy of motion. Dont waste time by walking all over your room when you could have planned better to have everything close by. Shoot us a pic when you're through!! FM12
FM12 is offline  
Old April 1, 2007, 04:00 PM   #6
JoeHatley
Senior Member
 
Join Date: July 1, 1999
Location: Iowa
Posts: 2,135
Quote:
I have a room I am going to build in my attic for mainly reloading.
Not in the attic, but a converted laundry room. I had the remodeling contractor build the bench and stain it to match the other wood trim.



Nothing fancy, just a simple basic bench. 4X4 legs and a couple layers (plywood & pine) for the top. Shelf is a simple 1X10 pine.

Joe
__________________
Go NRA
JoeHatley is offline  
Old April 2, 2007, 10:45 AM   #7
lgsracer
Member
 
Join Date: March 25, 2007
Location: Bayou La Batre AL
Posts: 54
If you are going to build from scratch go big. Here is a bench design heavy enough for swaging and case forming. Courtesy of " The Handloader's Manual of Cartridge Conversions (3rd edition)".
Attached Files
File Type: pdf bench.pdf (175.4 KB, 220 views)
File Type: pdf bench_002.pdf (250.4 KB, 132 views)
lgsracer is offline  
Old April 23, 2007, 01:50 AM   #8
mattgreennra
Member
 
Join Date: April 15, 2007
Location: Columbus, Ohio
Posts: 93
If you melt lead or tumble in that room I would be sure to install a large exhaust fan.

I'm paranoid about cancer dust personally. I wear a 3m breathing/painting mask when I use my tumbler.

Also there are some cool bins you can get @ lowe's for sorted brass. here's a link.
(my post is towards bottom under "Gnarkill"
http://www.thehighroad.org/showthrea...=218188&page=6
mattgreennra is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:54 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07622 seconds with 8 queries