The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 28, 2007, 09:27 PM   #1
JRD
Member
 
Join Date: February 27, 2007
Posts: 15
Cleaning Brass

Lets here how some of you clean your brass, I have a ton of brass that I need to clean before I can tumble it. I'm talking about cleaning dirty, dirty brass that has been in the mud and dust. Any ideas will be appreciated. Thanks
JRD is offline  
Old February 28, 2007, 09:43 PM   #2
rwilson452
Senior Member
 
Join Date: June 10, 2004
Location: Tioga co. PA
Posts: 2,342
If you have one and can get away with it. Get one of those clothes bags the ones like a fine fishnet. put the brass and a few rags in the bag. toss it in the clothes washer with some heavy duty pants. Hot water. gentile cycle will hold down the noise. take them out before the spin cycle. dump the brass in a colendar and rinse in the sink. put them boiling water bring water to a boil. restrain shake a lot. and put on a cookie sheet place in a preheated oven at 200. for 30 minutes. the idea is to get them in the oven while they are still hot. so don't shake too long. When on the cookie sheet be sure none of the brass is mouth up. they must be on their sides. and not stacked. A single layer.

Naturally, when they come out of the oven they are too hot to touch. I use one that has a lip. an old beat up one I picked up at a garage sale.
rwilson452 is offline  
Old February 28, 2007, 09:47 PM   #3
Ruger4570
Senior Member
 
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
If I ever put my dirty brass in the clothes washer with my wife around,,, well,, I probably would be able to sing in a Boys Choir after that.
Ruger4570 is offline  
Old February 28, 2007, 09:49 PM   #4
swmike
Senior Member
 
Join Date: June 25, 2005
Location: Marysville, WA
Posts: 658
I found by accident one day that RV "Black Streak Remover" works great in cleaning brass. No ammonia in it and it is safe for painted surfaces so it won't harm the brass. Takes out the soot and most all the dirt accumulated on the outside. I have also tumbled brass in my RCBS Sidewinder using water and Cold Water Laundry Detergent. No foam and it cleans good.
__________________
My definition of Gun Control--- A steady grip and hitting your target.


"In God we trust, all others are suspects."

"If I shoot all the ammo I am carrying, either I won't need any more, or more won't be of any help".

____________________________________________
swmike is offline  
Old March 2, 2007, 12:54 AM   #5
mrawesome22
Senior Member
 
Join Date: November 9, 2005
Location: Ohio, Appalachia's foothills.
Posts: 3,779
I found a bunch of .40S&W brass after the snow melted that was full of mud and gunk. I put them in the sink with dish soap and hot water and strirred with my hand. It got all the major stuff out. Tumbling will be next.
mrawesome22 is offline  
Old March 2, 2007, 07:59 AM   #6
Zippy06
Senior Member
 
Join Date: January 1, 2007
Location: S.E. MI
Posts: 117
Sink , dish soap, and hot water.
If really burned and/or tarnished. Use some Tufnut. From Lyman.
I use 90/80 % corn cob, 10% Tufnut, and brass polish. Gets that, bad burn mark, from using Titegroup.
__________________
Zippy06.
U.S.N. Vet. NRA.
Lee Turret(circa 1986). 9mm, .357 Mag., .40 S&W, .223 Rem., .30-30 Win., .308 Win.
G17, S&W 686, G22C, Colt H-Bar, Marlin, Savage 10FP. Be safe. Be happy
Zippy06 is offline  
Old March 2, 2007, 09:11 AM   #7
40MM
Member
 
Join Date: April 15, 2006
Posts: 69
I normally chuck my brass in some gasoline, leave it for a half hour, then rinse out with water and dishwasher detergent.
40MM is offline  
Old March 2, 2007, 11:24 AM   #8
wicker
Member
 
Join Date: February 18, 2007
Location: Iowa
Posts: 31
Last weekend I bought nearly 1000 once fired Speer 38spcl nickel brass at a gun show, for $5. They came from a local state prop. range and were full of dried mudd. I split the brass up between 2 coffee cans filled with hot water. I allowed them to soak for and hour or two and then drained. You can also put the lid on and give them a good shaking. Repeating this method three or four times left me with dirt free cases. When dry I put them in my Cabela's vibratory cleaner with cobb media. They came out looking like a new watch. I would think adding a touch of soap, if need be, wouldn't hurt a thing.

Not to put down anyones elses procedures, but I'd be reluctant to use any solovents, fuels, or cleaners other than simple soap that weren't intended for cleaning brass. Nor do I see the need. Water cleans away dirt and grime, even grease or oils with the addition of a little soap. As far as tarnish or light corrosion goes, that's what the tumbler is for. I'm no pro and I've only been doing this for a year, but that's is my humble opinion.

rwilson452
The washer idea (if you can get away with it) is a good one. Though I don't dare use it, my wife had a net bag used for washing nylons. I'd imagine even a nylon would work as a shell bag. A question though. Why the oven step? Are you trying to dry the brass or someting else with that step?
wicker is offline  
Old March 2, 2007, 11:28 AM   #9
rwilson452
Senior Member
 
Join Date: June 10, 2004
Location: Tioga co. PA
Posts: 2,342
the oven is just for fast dry. putting it in a dryer is just too much noise

The bag your wife uses for her nylons is just what I was talking about. you can get them is several sizes.
rwilson452 is offline  
Old March 2, 2007, 01:42 PM   #10
JRD
Member
 
Join Date: February 27, 2007
Posts: 15
Rice?

Have any of you tried tumbling with rice instead of regular media? I heard it worked well for really dirty casings and it doesnt cost as much as regular media.
JRD is offline  
Old March 2, 2007, 05:49 PM   #11
rickh
Member
 
Join Date: January 10, 2007
Posts: 47
For a nice shine....
Add automotive finish 3m brand "Swirl Make Remover" to corn cob, set timer on vib cleaner for 2 hours....
Takes the stains off and makes em shinny.
Rick H...
rickh is offline  
Old March 2, 2007, 09:57 PM   #12
cheygriz
Senior Member
 
Join Date: May 11, 2002
Location: high up in the rockies
Posts: 2,232
If you have a concrete mixer, or have access to one, put the brass in there with warm water and liquid Tide for 20-30 minutes, then rinse. You won't even need to tumble after this wash.

This is what commercial reloaders use.
__________________
If you think a mighty military force is expensive, wait 'til you see what a weak one costs.
cheygriz is offline  
Old March 3, 2007, 02:46 AM   #13
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 3,099
"...in the mud and dust..." Go to a dollar store and buy a collander. Brass in, run 'em under the tap. That'll take off any mud and dust. Then onto a cookie sheet and into the oven, set on warm, for about 15 minutes. Dish soap will leave a thin film on the brass. No big deal as you're tumbling, but it'll likely muck up your media faster.
Buy replacement media in a pet supply shop. Crushed corn cobs and walnut shells are sold as small pet bedding. A 50 pound bag runs less than $10 or so.
T. O'Heir is offline  
Old March 3, 2007, 09:11 PM   #14
tomf52
Member
 
Join Date: August 5, 2005
Posts: 46
Put the shells in a bucket. Add really hot water , just enough to cover the shells plus a tad more. Add a healthy squirt of dish detergent and a few ounces of bottled lemon juice.Sit vigorously for a few minutes. Let soak for an hour. Dump and rinse. You will have really bright and shiny casings.
tomf52 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:12 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09247 seconds with 7 queries