The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 14, 2007, 10:57 PM   #1
bloodtrail
Member
 
Join Date: December 26, 2006
Location: Wisconsin
Posts: 66
New to Reloading Questions

Im seriously thinking of getting into reloading my own handgun rounds.
Now, I would like to load .38 specials, .357, and .40 S&W.
I read a thread on here that said that the Lee Classic Turret Press was a decent reasonably priced unit to start up with.
Based on the calibers I listed, would someone be able to make a "shopping" list of what all I would need to get started? Bare bones to do the job, and then add some items that may be nice to have as cash comes available!
Maybe reloading is a jump into the deep end of the pool right from the get go type of deal and I need it all.
But if someone could help me out by listing what I all would need based on that press that would be great!
Maybe thats not the press to get? But from what I read it seemed like a good unit and affordable to begin with!
bloodtrail is offline  
Old January 14, 2007, 11:17 PM   #2
rwilson452
Senior Member
 
Join Date: June 10, 2004
Location: Tioga co. PA
Posts: 2,361
Basic stuff

There is a two part sticky at the top of this forum on reloading basics. I suggest you start there. Get the book and come back when your ready.
rwilson452 is offline  
Old January 14, 2007, 11:28 PM   #3
CrustyFN
Senior Member
 
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
Lee Auto Disk Powder Measure Riser.
Lee Adjustable Charge Bar Auto Disk. ( not needed but nice to have )
Lee Pro Auto Disk Powder Measure.
Lee Safety Prime Small and Large Primer Feeder.
Lee Classic Four Hole Turret Press.
Lee Deluxe Handgun Four Die Set ( your calibers ).
Extra turrets. ( easy to leave the dies set up and change turrets )
Scale.
Tumbler for brass.
Caliper.
Hammer type bullet puller. ( we all make mistakes )
A couple of reloading manuals.

You can buy the classic turret kit at Cabelas for $150. It includes the press with one turret, pro auto disk powder measure, auto disk riser, safety prime large and small, safety scale and a rifle charging die. If you buy the kit it will cover most of the list at the top. I think that should cover it except for components.
Rusty
__________________
I don't ever remember being absent minded.
CrustyFN is offline  
Old January 14, 2007, 11:29 PM   #4
Daniel BOON
Senior Member
 
Join Date: June 5, 2005
Location: Henderson NV
Posts: 360
what I want for christmas

so you want to reload?
Lee sells package reload stuff, with just about everything u need to get started........but since u asked.
a press/scale/dies/brass/primers/powder/bullets/reload book. when I started, I c clamped the press to the kitchen table. it didn't very well.
a good reload book; rcbs's book takes you threw step by step of how-to reload. I can't think of anything else. when you get a ways down the road, and haven't blown anything up, you can tweek the reloads to fit the gun; if you were in this room right now, I would tell you to go buy/or get one at the library, a how-to book, look at it front and back, then decide what you need.
Daniel BOON is offline  
Old January 14, 2007, 11:36 PM   #5
cloudcroft
Senior Member
 
Join Date: August 5, 2006
Location: Colorado Springs, CO
Posts: 562
bloodtrail,

RTFM: http://www.thefiringline.com/forums/...d.php?t=230171

-- John D.

P.S. See Dave...I told you again! It never ends...
cloudcroft is offline  
Old January 15, 2007, 12:43 AM   #6
JJB2
Junior member
 
Join Date: December 14, 2005
Posts: 558
i like reloading off single stage press... my friend and mentor uses a lee turret press but i like the way i can see what i'm doing better than with the turret press.... actually i use two single stage presses side by side in my own method of reloading..... but it works for me.......
JJB2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:01 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07554 seconds with 7 queries