The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 9, 2006, 10:20 AM   #1
ZeroJunk
Senior Member
 
Join Date: August 14, 2006
Location: Browns Summit NC
Posts: 2,461
Downloading Magnums

Has anybody had any accuracy success with light loads in something like a 300WBY.I tried with H4831SC and got a 6 inch group.Would a faster burning powder work better or is it a lost cause.Was aiming for something in the range of a 30/06 factory load.
ZeroJunk is offline  
Old October 9, 2006, 12:01 PM   #2
rnovi
Senior Member
 
Join Date: July 10, 2005
Location: So. Cal.
Posts: 401
Zero,

First off, good on you for trying to download such a big cartridge to make it more shootable on a daily basis. I do the same thing with my .350 Rem Mag - it's a lotta fun and I have even worked up Bunny loads using pistol bullets.

BUT, and I do mean BUT, do NOT go into this blind. An undercharged case can be just as dangerous as an overcharge! The first thing I am going to recommend is to go to www.midwayusa.com and buy a "Loadbooks USA" on your cartridge. They are around $8 or so and contain ALL the load data from any published resource on your cartridge in one place. I'm very willing to bet that someone (Speer, Lyman come readily to mind) have already worked up reduced power loads for you.

Start there.

IF nothing is available, send me a PM or the like and we can exchange phone numbers. I'll be glad to tell you how I go about creating a reduced load - but I'm sure not going public with it lest someone mis-interpret something and get in trouble!
__________________
Robert N.

"Remember, Eagles may soar but Weasels don't get sucked into jet engines!"
rnovi is offline  
Old October 10, 2006, 06:33 AM   #3
toolguyb
Member
 
Join Date: March 1, 2006
Posts: 73
Zero

I download my 300 wby. I use IMR 3031, 58 grns, and 180 grn rem psp.
I have wrote down 2700 fps.

rnovi is correct about the danger of downloading powder charges. I also would make sure that I only used a published data.
toolguyb is offline  
Old October 10, 2006, 09:19 AM   #4
ZeroJunk
Senior Member
 
Join Date: August 14, 2006
Location: Browns Summit NC
Posts: 2,461
Thanks for the responses.I don't want to go below the published minimums.My problem has been that I can't seem to find one that is accurate.
ZeroJunk is offline  
Old October 10, 2006, 09:30 AM   #5
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 35,251
Downloading a magnum-size cartridge often creates a huge dropoff in accuracy.

The cases are just too large and the pressure curves to erratic.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06883 seconds with 7 queries