The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 28, 2000, 10:12 PM   #1
saands
Senior Member
 
Join Date: November 14, 1999
Posts: 1,551
I have never used one ... but I have been playing with different loads and the "shake-the-powder-from-a-dipper-onto-the-scale" method is getting a little tiresome! If anyone likes them, can you please recommend one ... I'd like to stay in the $30 and under range ... it is a completely non-essential item afterall
Thanks,
saands
saands is offline  
Old September 29, 2000, 07:05 AM   #2
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 13,903
Have one, rarely used.

Best trickler is Redding's (weighs a pound!), available through Midway, Graf & Sons, Natchez, Wideners, etc...

------------------
"All my ammo is factory ammo"

WESHOOT2 is offline  
Old September 29, 2000, 08:24 AM   #3
Jack Straw
Senior Member
 
Join Date: July 26, 1999
Location: Georgia
Posts: 362
I have Lyman's and I use it any time I am loading for rifles. I use a Lee dipper to dump a slightly low charge onto the scale and then use the trickler to bring the charge up to the desired level. I don't know the price, but it is a plastic model so it should be in your range. It doesn't have the benefit of a heavy base, but it works well for my purposes.

Jack

[This message has been edited by Jack Straw (edited September 29, 2000).]
Jack Straw is offline  
Old September 29, 2000, 09:01 AM   #4
Stephen A. Camp
Staff In Memoriam
 
Join Date: April 16, 1999
Posts: 2,570
Hello. I use an RCBS trickler for loading rifle rounds. Best.
Stephen A. Camp is offline  
Old September 29, 2000, 09:23 AM   #5
JoeHatley
Senior Member
 
Join Date: July 1, 1999
Location: Iowa
Posts: 2,135
I use one from RCBS. I usually try to find a powder dipper that holds just a bit too little, and then finish off with the trickler.

It's not real fast, but I do get accurate weights.

Good Luck...

Joe


------------------
Go NRA
JoeHatley is offline  
Old September 29, 2000, 12:11 PM   #6
Bud Helms
Staff
 
Join Date: December 31, 1999
Location: Middle Georgia
Posts: 12,978
saands,

Check email.
Bud Helms is offline  
Old September 29, 2000, 03:00 PM   #7
WalterGAII
Junior member
 
Join Date: November 7, 1999
Posts: 1,516
I have the standard, metal RCBS trickler, which I never use. The $15.00 electric Midway trickler works very well for me.
WalterGAII is offline  
Old September 30, 2000, 07:00 AM   #8
rr41mag
Senior Member
 
Join Date: June 25, 2000
Location: Biloxi, Miss.
Posts: 180
saands I have 2 rcbs tricklers if you want one email me your address and I'll send it to you
rr41mag is offline  
Old October 2, 2000, 12:05 PM   #9
Ala Dan
Member in memoriam
 
Join Date: August 13, 1999
Location: In The HOT, Humid, and Mu
Posts: 6,117
Yep, I use the RCBS metal trickler, and never
had a problem with it.

Regards,
Ala Dan, N.R.A. Life Member
Ala Dan is offline  
Old October 2, 2000, 01:23 PM   #10
DAL
Senior Member
 
Join Date: October 15, 1999
Location: Colorado Springs, CO, USA
Posts: 653
I use a cheap little plastic one when I reload for my rifle. I couldn't get exact loads without it.
DAL

------------------
Reading "Capitalism: The Unknown Ideal," by Ayn Rand, should be required of every politician and in every high school.

"Guard with jealous attention the public liberty. Suspect everyone who approaches that jewel. Unfortunately, nothing will preserve it but downright force. Whenever you give up that force, you are ruined."
--Patrick Henry, during Virginia's Convention to Ratify the Constitution (1788)

GOA, JPFO, PPFC, CSSA, LP, ARI, NRA
DAL is offline  
Old October 2, 2000, 08:12 PM   #11
Turk
Senior Member
 
Join Date: May 30, 2000
Location: USA
Posts: 517
I use the REDDING it works great ($14.00) it has a heavy base so it won't get moved around or knocked over easy.

But to be quite frank, my REDDING Benchrest #3BR Powder Measure meters ball powder 1/10 to 2/10th all the time. This is sufficient for my shooting and a lot less hassle.

Years ago I shot loads from the measure and then exact loadings using the trickler couldn't see any advantage. Again for my style of shooting which at that time was High Power Service Rifle.

Turk
Turk is offline  
Old October 4, 2000, 09:33 AM   #12
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 2,584
When working up a load in .1 gr increments, I use a trickler.

When loading all the same wieght, I don't.
Clark is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08645 seconds with 7 queries