The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 20, 2000, 01:28 PM   #1
westvirginia
Member
 
Join Date: March 10, 2000
Location: Atlanta
Posts: 23
I have read that the proper seating depth for a rifle load is typically two to three thousandths before the bullet contacts the lands. I would like to know:

A. Is that the generall concensus? If not, what is the proper depth?

B. How do I determine the overall length for the cartrige for my specific rifle?
(most important, because I can always vary my depth for a given load)

Any tips/information would be greatly appreciated. I'm trying to come up with some accurate rifle loads.

------------------
Is life so dear, or peace so sweet, to be purchased at the price of chains and slavery?
westvirginia is offline  
Old September 20, 2000, 06:09 PM   #2
Big Bunny
Senior Member
 
Join Date: August 9, 1999
Location: New South Wales - Australia
Posts: 605
WV...I have found it is a matter of what the rifle "likes" ...but start with saami/factory deapths and work up. I find that a candle-smoked projectile does not work for me, so I highly polish my projectiles and 'inch' it forward using calipres and a puller until it is engraved by the lands...then back it off at least +30 thou to allow for any material/procedure irregularities/unburned powder/dirt etc and work from there. It is no good for hunting(thats me !) to safely decock a round - only to find that the barrel is completely blocked and 38gn of powder is through the tight Tikka 55 mauser action! This is the end of any days hunting when it happened once, as I had no time to rod the .17Rem out before dusk as the cleaning rod and gear were in the SUV a mile away, also pressures can be much higher seated into the lands and less powder is needed consequently-
but benchresters are good to talk to about this.
Overall lengths are given in any good loading book(I like LYMAN's 47th)and case 'trim to length data' is essential for safety too...as is a good trimmer(Redfield is mine) and a good electronic caliper(electronic is not essential - but nice).
I hope this helps a bit!

Lack of bullet concentricity is a contributing anti-accuracy factor more in my case than the above, and FLRSizing also an important factor in chambering properly only in my W30/30 ,as all the rest do 10 to 15 reloads without it - being mauser front lockers.
The Hornady Reloading Book is worthwhile to read also, as they stress safety and testing one thing at a time -in small 10% steps.

Well- WV, thats my 5c worth, welcome to the cautious and conservative world of reloading...or should that be "ammo assembly"? BB

------------------
If we shooting sportspersons don't hang together... we will all hang separately !
Never knock another's different shooting interest or discipline...REMEMBER we are all but leaves on the same tree of freedom.
Big Bunny is offline  
Old September 22, 2000, 01:54 AM   #3
bk40
Senior Member
 
Join Date: January 12, 1999
Location: Mississippi
Posts: 1,004
wv,

the best product I've come across is Stoney Points chamber-all gauge and bullet comparator. Sinclair's www.sinclairintl.com/ carries these and several other products used to precisely measure ogive/lands lenght.
bk40 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:40 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05980 seconds with 7 queries