The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 17, 2000, 11:59 PM   #1
Mylhouse
Senior Member
 
Join Date: November 9, 1999
Location: Tempe, AZ
Posts: 444
Do any of you use RCBS or Lee (or whatever) carbide dies in your 550 instead of the Dillon dies? I noticed that Dillon's 3-die set run about $50, whereas the RCBS carbide 3-die sets go for about $30. Hey, if I can save $20 per caliber, and get the same quality, why not?
Mylhouse is offline  
Old September 18, 2000, 01:11 AM   #2
Chris McDermott
Senior Member
 
Join Date: March 30, 2000
Posts: 245
Dillon dies have the quick disassembly cleaning feature; probably the reason for the higher price. Lee dies are usually the cheapest, but are typically shorter than other maker's dies. To use them in a Dillon press it's usually necessary to put the lock ring UNDER the die plate. RCBS makes dies for everything, and will even make dies for your own custom wildcat design if you are willing to pay the price.
I prefer Redding Pro Titanium carbide dies for my pistol reloding as they come with seperate seating & crimping dies; and have the Redding Profile Crimp dies for revolver calibers that need to be roll-crimped. They aren't cheap, but your reloading dies will probably outlast you.
Chris McDermott is offline  
Old September 18, 2000, 02:38 AM   #3
char923
Senior Member
 
Join Date: February 18, 2000
Location: Anchorage AK
Posts: 237
I use Dillon and RCBS dies, I like them both. I like the Dillon a little better because of the quick disassembly cleaning feature. speciality when reload with lead bullets.
char923 is offline  
Old September 18, 2000, 08:55 AM   #4
Jack Straw
Senior Member
 
Join Date: July 26, 1999
Location: Georgia
Posts: 362
The dies on my 550 are a mix of Dillon and Lee dies. Like Chris said, the lock ring on the Lee dies must be put under the toolhead, but otherwise they work just fine.

Jack
Jack Straw is offline  
Old September 18, 2000, 09:03 AM   #5
Watchman
Junior member
 
Join Date: August 8, 2000
Location: ARKANSAS
Posts: 484
You can use anybodys dies in the Dillon.

I used to use RCBS and Lee and Lyman but after a period of time I went exclusivley to Dillon dies . Why ? Because they are made for a progressive press. They work better.

Example: The decapping die has a much bigger radius on the mouth than any other die. AS a result , you dont have to guide the bullet into the die like you do with most brands.Its easier and quicker.

I like the bullet seater die. Same thing.
I like the taper crimp dies. Much stronger and more consistent than a roll crimp.

IF you already have the dies and want to save the money, use what you have.

IF you are buying the dies new...spend the extra money and buy the Dillon dies. You wont be sorry you did.
Watchman is offline  
Old September 18, 2000, 11:00 AM   #6
Alan B
Senior Member
 
Join Date: August 26, 1999
Posts: 335
I use dillion pistol dies ( if the caliber is available) and LEE rifle dies.

Chris, Jack
for the lee dies take the lock ring off and put it back on the die upside down and you can put it in top of the tool head.
Alan B is offline  
Old September 18, 2000, 12:20 PM   #7
JHS
Senior Member
 
Join Date: November 30, 1998
Location: Goodwell,Ok.
Posts: 505
I am working on a 550b deal now. So with the Dillon dies, do I need a factory crimp die also?
JHS is offline  
Old September 18, 2000, 01:04 PM   #8
EQP
Senior Member
 
Join Date: March 31, 2000
Location: Schaumburg, IL
Posts: 154
JHS,

What caliber are you going to be reloading for?

Evan
EQP is offline  
Old September 18, 2000, 05:08 PM   #9
jtduncan
Senior Member
 
Join Date: December 5, 1999
Location: Seattle, Washington, USA
Posts: 1,681
Use Lee carbide dies all of the time - just flip the Lee lock nuts upside down and they lock the die down real tight!

------------------
The Seattle SharpShooter - TFL/GT/UGW/PCT/KTOG
jtduncan is offline  
Old September 18, 2000, 07:01 PM   #10
slickpuppy
Senior Member
 
Join Date: August 29, 1999
Posts: 928
I only use Redding dies in my 550. I have 2 sets of Dillon dies, but found the Reddings to be unbeatable and so nicely made it would be a travesty to use anything else
slickpuppy is offline  
Old September 18, 2000, 11:56 PM   #11
El Rojo
Senior Member
 
Join Date: February 4, 2000
Location: People's Republik of Kalifornia
Posts: 2,057
I bought .308 and .30-06 Dillon dies, then .30 carbine was Lee, and .45 and .40 are Hornady. They all work fine for the RL 550B. I had a guy give me some RCBS 9mm dies, but I haven't gotten around to trying them out yet. I am satisfied with them all. For reloading cheap pistol loads, why spend an arm and a leg?
El Rojo is offline  
Old September 19, 2000, 12:42 AM   #12
ol blue
Member
 
Join Date: January 21, 2000
Location: USA
Posts: 62
For the pistols I like the Dillon dies, for all the reasons previously stated. For my .308 my Forster b.r. dies work just fine in the 550. (something I was a little concerned about when I got the 550, because of the moving chamber design of the Forster seater)...ol blue
ol blue is offline  
Old September 19, 2000, 06:03 PM   #13
johnwill
Senior Member
 
Join Date: April 6, 2000
Location: PA
Posts: 3,451
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by JHS:
So with the Dillon dies, do I need a factory crimp die also?[/quote]

Nope. The Dillon die sets have a crimp die, and they work just fine. Most of my pistol dies are Dillon.


johnwill is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.10214 seconds with 7 queries