The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old August 21, 2000, 08:37 AM   #1
Jack Straw
Senior Member
 
Join Date: July 26, 1999
Location: Georgia
Posts: 362
The subject pretty much says it all. I've been shooting 165grainers, but was thinking of trying some 150gr (both will be for whitetail) and was curious to see what others have found to be their preferred powder.

I almost forgot to ask: Where can I find a powder burning rate chart?

Thanks

Jack

[This message has been edited by Jack Straw (edited August 21, 2000).]
Jack Straw is offline  
Old August 21, 2000, 10:49 AM   #2
alan
Senior Member
 
Join Date: June 7, 1999
Posts: 3,745
while there are certainly other powders that would work, try 4895, either Du Pont of Hogdon.

As for burning rate charts, I think some of the NRA rreloading manuals had published them
alan is offline  
Old August 21, 2000, 06:11 PM   #3
ol blue
Member
 
Join Date: January 21, 2000
Location: USA
Posts: 62
I like 4064. I'm also trying W748 right now but so far have not done as well as 4064....ol blue
ol blue is offline  
Old August 21, 2000, 10:40 PM   #4
Target Shooter
Senior Member
 
Join Date: May 19, 2000
Posts: 176
I like Accurate Arms 2520 powder the best.
I also got a good load for 150 grain bullets from a gun magazine about a year or two ago that recommended H380.
My Remington PSS will shoot 1/2" groups with the following load:

Federal Brass
Federal 215 Primer (Mag)
48.5 grains of H380
150 Grain Winchester Silver Tip bullet.

Use the Mag primer otherwise the H380 will burn dirty.
Target Shooter is offline  
Old August 22, 2000, 09:45 AM   #5
BMiracle
Senior Member
 
Join Date: February 12, 2000
Posts: 159
I have had good luck with H4895 and Varget sitting under Nosler Ballistic tips ro Hornady SST's.
BMiracle is offline  
Old August 23, 2000, 06:15 PM   #6
Monkeyleg
Senior Member
 
Join Date: January 25, 2000
Posts: 4,625
N140 has worked well for me. Will have to try some of the other powders mentioned here.

Dick
Want to send a message to Bush? Sign the petition at http://www.petitiononline.com/monk/petition.html and forward the link to every gun owner you know.
Monkeyleg is offline  
Old August 24, 2000, 01:36 PM   #7
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 2,648
Jack. There was an article about a year or so ago on the "best" powders for the .308.
Being a person who prefers the "ball" powders, I use W-760 in my .308 loads. According to that article, however, Winchester stated that W-748 was designed specifically for the .308. I haven't tried it yet, but I may before this hunting season.
W-748 is supposed to give the highest velocity of the Winchester powders. It's good stuff. I like it.
I don't post loads on the forums, but I will pass them on if you E-mail me and request them. All I can say about these loads, it that they have proved safe and accurate in the 7 different .308 rifles I own.
Paul B.
Paul B. is offline  
Old August 24, 2000, 02:52 PM   #8
sundog
Senior Member
 
Join Date: November 22, 1999
Location: Green Country, OK
Posts: 730
Jack, powder burn rate chart? Try:
www.reloadammo.com

sundog

------------------
safety first
sundog is offline  
Old August 24, 2000, 05:33 PM   #9
Patrick Graham
Junior member
 
Join Date: January 18, 1999
Location: Kokomo, Indiana USA
Posts: 674
Varget
Patrick Graham is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07731 seconds with 7 queries