The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 22, 2000, 04:42 PM   #1
El Rojo
Senior Member
 
Join Date: February 4, 2000
Location: People's Republik of Kalifornia
Posts: 2,057
I was excited to reload another 100 rounds of my Hornady VMax with some 4895 yesterday. As I was setting up, I noticed what seemed like an excesive ammount of powder spilling out of the powder die as I lowered the platform on my RL 550B with Dillon powder measure.

Here is my concern. I might have been living with this powder spillage the last hundreds of rounds I have loaded and have only now only really noticed it. What was once not a real big deal, I am now thinking is a mighty big waste of some powder. I spent hours trying to figure out a way around this thing. I read in the manual where it said the IMR pencil leads don't load very consistant with Dillon powder measureres. I tried tapping against the powder measure as I slowly lowered the platform, but that made every other charge excessive.

What are your suggestions? Was I fine all along and just now noticed I was spilling a little bit of powder and there is nothing I can do about it? Or should I try some of the ball powders? If ball powders, I need some suggestions. Thanks all.
El Rojo is offline  
Old May 22, 2000, 07:59 PM   #2
Bud Helms
Staff
 
Join Date: December 31, 1999
Location: Middle Georgia
Posts: 13,002
El Rojo,

The IMR powders are fantastic in every respect except flowing through a powder measure. That's why I have avoided using them for the past ten years. Winchester, Hodgdon , Accurate and now Vihta Vouhri (sp?) all have ball powder or short extruded powders to substitute at most every burn rate you could want.

On the other hand, it sounds like the powder bar may be sticking. I'd check it for "dry and clean" and make sure both return springs are in good shape.
Bud Helms is online now  
Old May 22, 2000, 11:08 PM   #3
Steve Smith
Senior Member
 
Join Date: December 9, 1999
Posts: 4,131
I'm a real newbie at reloading, but I recall my local Dillon rep. telling me that if I ever had problems with powder flow, try putting one of those foot massagers on the table (running) while you're loading. Maybe I'm way off base with your needs, but maybe I can help.
Steve Smith is offline  
Old May 22, 2000, 11:13 PM   #4
alan
Senior Member
 
Join Date: June 7, 1999
Posts: 3,745
In the past, I loaded both 30-06 and 308 ammunition, using 4895 on a Dillon 550. Never noticed any powder spillage. Also used 4350 for the 30-06, which is "worse" than 4895.

As for 4895 and the Dillon measure, or most any other powder measure for that matter, extruded powders, due to their "sticklike shape" simply do not feed all that well, especially compared to ball powders.

The "problem" is nothing that cannot be "lived" with however.
alan is offline  
Old May 22, 2000, 11:52 PM   #5
El Rojo
Senior Member
 
Join Date: February 4, 2000
Location: People's Republik of Kalifornia
Posts: 2,057
Thanks for your help. I think I will send off a letter to Dillon too to see what they say. I think I have been dealing with it all this time, just yesterday for some reason it was suddenly the most horrible event in history. What a shame to waste away my whole day worrying when I should have been spitting out VMax bullets.

Anymore opinions would still be appreciated.
El Rojo is offline  
Old May 23, 2000, 08:49 AM   #6
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,468
If you're loading for .308, there are lots of powders which work very well as to velocity and accuracy and also function through a powder measure. IMR powders just aren't "built right" to be uniform through a measure.

Best luck, Art
Art Eatman is offline  
Old June 1, 2000, 02:01 AM   #7
El Rojo
Senior Member
 
Join Date: February 4, 2000
Location: People's Republik of Kalifornia
Posts: 2,057
To follow up on my powder spillage for any of you Rl 550B owners. I had the bolt and nut that holds the powder measure bar in too tight. As a result, when I started to lower the platform, the powder measure would stay in the up position until the little return bar started to pull it back down. At this time the rest of the powder was coming out of the measure cup as the .308 brass was way below the powder bell. This caused the powder to spill out onto the bench. I just loosened that bolt and nut a little and the powder measure came down on its own gravity, pushing the rest of the powder charge out and into the .308 brass instead of all over the bench.

Let me tell you what a relief it is to find out you are an idiot and that your machine is not broken. Live and learn.
El Rojo is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07155 seconds with 9 queries