The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 15, 2000, 09:37 PM   #1
bullet44
Senior Member
 
Join Date: February 21, 2000
Posts: 819
Looking for a "lite" practice load for my
springfield auto. Using either 230gr or 200
gr round nose(lead) which gives the best
accuracy 230 gr or does the smaller wt's do
best. also will the semi-wadcutters feed
in the auto's and how does there accuracy
compare to the round nose.???

------------------
bullet44 is offline  
Old March 15, 2000, 10:11 PM   #2
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,540
If everything is righteous, a 1911-type pistol will dang near feed empty brass.

I used to load 5.8 grains of 231 behind a 200-grain SWC as my IPSC load. You could go down to maybe 4.5 or 5.0 grains for a lesser recoil; whatever lets the gun cycle unless you want to change to a lighter spring.

Can't help on the comparative accuracy; I never worried about super-tight groups.

FWIW, Art
Art Eatman is offline  
Old March 15, 2000, 10:29 PM   #3
Fusternc
Senior Member
 
Join Date: November 9, 1999
Location: New Hampshire
Posts: 113
I have found that the following load is quite accurate in my fullsize Springfield "Loaded" 1911:

4.9grains of Bullseye behind a 200gr Rainier SWC or 200 gr Rainier flat point.

or

5.7 grains of Unique behind the 200gr Rainier Flat point or flat point.

The accuracy between the SWC and flat point is about the same for me in this gun.

My Springfield feeds both without a hitch.

Good Luck.


Nathan

Fusternc is offline  
Old March 16, 2000, 06:45 AM   #4
Joe D
Senior Member
 
Join Date: October 17, 1999
Location: Alabama
Posts: 455
Here's what works in my two Kimbers.
4.4 - 4.6 gr. Titegroup
200 gr. Magnus SWC
1.260" OAL
800 fps.
Win. or Federal primers
Sub 1" groups @ 25 yds.


Joe D is offline  
Old March 16, 2000, 08:00 AM   #5
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,270
I've noticed that, in general, the most accurate 45 loads use W231 or Bullseye.

------------------
"All my ammo is factory ammo"

WESHOOT2 is offline  
Old March 16, 2000, 04:57 PM   #6
Desert Dog
Senior Member
 
Join Date: September 22, 1999
Location: Dallas, TX
Posts: 473
My most accurate load is 5.0 grs of Win231 behind a 230 gr. RN lead bullet. OAL 1.26"...

have fun...



------------------
.45 Super... Fat and FAST...

"No provision in our Constitution ought to be dearer to man than that which protects the rights of conscience against the enterprises of the civil authority" - Thomas Jefferson
Desert Dog is offline  
Old March 16, 2000, 05:34 PM   #7
dwt
Junior Member
 
Join Date: March 7, 2000
Posts: 8
5grs-231,works real well for me,with any weight bullit.
dwt is offline  
Old March 18, 2000, 05:26 AM   #8
johnnybravo
Senior Member
 
Join Date: February 10, 2000
Posts: 100
3.8 gr Bullseye
4.0 gr 700-X
You might have to go to a lighter recoil spring, but those are cheap and easy to change.

------------------
johnnyb
A slow hit beats a fast miss.
johnnybravo is offline  
Old March 20, 2000, 01:33 PM   #9
Monkeyleg
Senior Member
 
Join Date: January 25, 2000
Posts: 4,625
Either 5.3 grains of 231 using a 230 gr RN lead bullet, or 7.5 grains of Accurate #5 over the same bullet. Velocity is around 750 fps for each load. I just like the #5 powder better because it's finer, and measures more evenly from my powder dispenser.

Dick
Monkeyleg is offline  
Old March 21, 2000, 06:57 PM   #10
char923
Senior Member
 
Join Date: February 18, 2000
Location: Anchorage AK
Posts: 237
with my 200gr SWC I use 6.7gr of N340 VihtaVuori in my IPSC loads.
char923 is offline  
Old March 27, 2000, 09:27 AM   #11
Hakwe
Junior Member
 
Join Date: September 26, 1999
Posts: 3
I get good results with 4.6g of Winchester WST and a 200g lead cast SWC
Hakwe is offline  
Old March 27, 2000, 09:56 AM   #12
tonyz
Senior Member
 
Join Date: January 29, 2000
Location: Wa
Posts: 922
I use 5.0 Grain's bullseye behind 200Gr SWCL.
Very light load and very accurate.

------------------
www.vote.com
tonyz is offline  
Old March 27, 2000, 11:03 AM   #13
JoeHatley
Senior Member
 
Join Date: July 1, 1999
Location: Iowa
Posts: 2,135
Here's another vote for Bullseye. I use 4.5 grains with a 200 grain LSWC cast Silver Bullet.

Gives good to great accuracy in a Ruger Blackhawk convertable, S&W 625, and two different Colt 1911 pistols.

Seems to work well in anything I use it in.

Joe


------------------
Go NRA
JoeHatley is offline  
Old March 28, 2000, 10:26 AM   #14
Svt
Junior member
 
Join Date: January 23, 2000
Posts: 467
4.7 Grains Win. 231 with 200gr LSWC 1.255 OAL .469 crimp
Svt is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.10318 seconds with 9 queries