The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 9, 2000, 07:27 PM   #1
TAckerman
Junior Member
 
Join Date: December 23, 1999
Location: Denver, CO USA
Posts: 13
How do you guys clean the lube off a few hundred loaded progressive press assembled .223 rounds?

There has got to be a safe, effective and quick way to do this.

Thanx,
ACK
TAckerman is offline  
Old March 9, 2000, 07:51 PM   #2
WalterGAII
Junior member
 
Join Date: November 7, 1999
Posts: 1,516
Just takes a few, safe, effective minutes with my Midway tumbler (vibratory) and treated cc media. If you use the spray-type lubricants, it's a lot easier.
WalterGAII is offline  
Old March 9, 2000, 11:16 PM   #3
BILLG
Senior Member
 
Join Date: February 12, 2000
Posts: 140
I agree with Walter. I e-mailed Dillon awhile back and they said it could to no harm as long as it was a vibrating tumbler and not a rotary tumbler,tumble cases about 15 min.I use Dillon spray case lube on all my cases even when using carbide pistol dies,the reduced lever effort makes it worthwhile. BILLG
BILLG is offline  
Old March 10, 2000, 07:14 PM   #4
HankL
Senior Member
 
Join Date: March 11, 1999
Location: The Sunny South
Posts: 2,174
10-4 to the above.
Hank
HankL is offline  
Old March 11, 2000, 09:43 AM   #5
dundee
Senior Member
 
Join Date: December 6, 1998
Location: mytown,mi,usa
Posts: 162
From comments I've read about tumbling finished ammo combined with other things concerning deactivated primers, I never vibrate loaded ammo. As the previous person stated it may be safer to vibrate ammo than tumble it, but why take risks unnecessarly. Vibrating the ammo at this point may be the fastest way, but try to vibrate only as long as mecessary.

I always vibrate my rifle brass first, lube it and size in on a single stage press, then vibrate it again to remove the lube. At this point I check the case length and do any case prep necessary. Now I feel ready to load 223 on the Dillon. It adds a step or 2 but I feel confidant of the quality of the ammo produced this way.

[This message has been edited by dundee (edited March 11, 2000).]
dundee is offline  
Old March 11, 2000, 10:51 AM   #6
Patrick Graham
Junior member
 
Join Date: January 18, 1999
Location: Kokomo, Indiana USA
Posts: 674
I lube, size on my rochchucker, tumble the lube off, then cycle them through my dillion. I have a sizing die in station one that is set up high enough not to size but to poke through the primer hole. This is just in case the hole is blocked by media.. Media in the primer pocket cost me an 8 point buck about 12 years ago.
Patrick Graham is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:22 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07442 seconds with 7 queries