The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 1, 2000, 05:27 PM   #1
Jack Straw
Senior Member
 
Join Date: July 26, 1999
Location: Georgia
Posts: 362
I was thinking of ordering a case of Fiocchi .45ACP from ammoman.com, but I've never fired Fiocchi ammo and I'm not sure of it's quality (I'm getting 230grFMJ just for target shooting). Also, I figured it would be a good way to start collecting .45 brass for reloading. Any comments on the quality of their brass?

Thanks much,

Jack
Jack Straw is offline  
Old March 1, 2000, 07:25 PM   #2
Peter M. Eick
Senior Member
 
Join Date: August 3, 1999
Location: Houston, Texas
Posts: 2,808
I have used it for practice rounds and now for reloading. It seems ok in 45acp. Nothing special. I think it is a bit thick compared to remington, but not as bad as PMC or such.



------------------
P229 Sport and 357 SIG, Perfection!
Peter M. Eick is offline  
Old March 2, 2000, 12:11 PM   #3
Oleg Volk
Staff Alumnus
 
Join Date: December 6, 1999
Location: Nashville, TN
Posts: 7,022
Is thick brass bad somehow?
Oleg Volk is offline  
Old March 2, 2000, 11:42 PM   #4
saands
Senior Member
 
Join Date: November 14, 1999
Posts: 1,551
I don't think thick is necessarily bad ... but if the outer dimensions are set in sizing, then the case will have a reduced capacity ... which eats up a little of the safety margin in your loads ... if all your brass is Fiocchi, then the loads you work up should be fine ... I don't even "know" that the Fiocchi is thick :> ) I bought a case of Fiocchi in .40S&W from bulkammo.com and love it ... and reload it!
saands
saands is offline  
Old March 10, 2000, 01:12 PM   #5
Kenneth L. Walters
Senior Member
 
Join Date: September 2, 1999
Location: flagstaff, arizona
Posts: 476
The only Fiocchi ammunition that I've used is their speciality stuff. It is certainly better than nothing but, well, the quality seemed to vary all over the place. Some was near perfect. Some wasn't.
Kenneth L. Walters is offline  
Old March 10, 2000, 04:47 PM   #6
LongDuck
Member
 
Join Date: September 15, 1999
Posts: 97
For reloading .45ACP, my brass order of preference is as follows, by headstamp; (best to worst)

S&B - consistent brass, tightest primer pockets
R*P - good quality
'Triangle' 9x - South African, good quality
Federal (and FC 9x) - some 'crimped' primers
PMC - okay quality
TZZ - Fiocchi
Hornandy - usually Starline, but don't see too many
CorBon - sometimes bulged (+P loading)
Anything else - range brass and practice reloads only.

If I can't identify a full 50 round box of brass, I don't reload for it for IDPA competition - a friend gets it as 'guaranteed to fire once' ammo. HTH,
LongDuck is offline  
Old March 11, 2000, 02:22 AM   #7
Pooch
Member
 
Join Date: March 3, 2000
Posts: 38
ssands,

thick brass does not eat up any saftey margin. thick brass, as in military brass will:

a. hold more pressure
b. neccesitate less powder for the same results as thin brass due to decreased case capactiy.

No flame intended!

My fiocchi is fine ammo, I have not loaded any of the brass good shooting.
Pooch is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07087 seconds with 7 queries