The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old May 11, 2006, 12:36 PM   #1
kidvillain41300
Member
 
Join Date: May 10, 2006
Location: Prescott,AZ & Middleburg,FL
Posts: 16
NEF 50cal Breech Plug stuck

I have a relatively new NEF 50cal muzzleloader and the breech plug was taken out by me after the first shooting, did the usual cleaning with soap and water, air compress dry and then ballistol lube. Put some anti-seize on the breech plug and reinstalled. Shot the gun a 2nd time, did the same cleaning and all but now the breech plug will not go all the way in. I backed it out and checked the threads and they look fine.........Any clues on this?.....I know a new barrel only runs about $90 so its not the end of the world, I just dont know why or what caused this breech plug not screw all the way in. Thnx
kidvillain41300 is offline  
Old May 11, 2006, 11:42 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,429
Almost sounds like crud in the threads or a ding in the plug threads. Did you drop it at some point?
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old May 12, 2006, 10:58 AM   #3
kidvillain41300
Member
 
Join Date: May 10, 2006
Location: Prescott,AZ & Middleburg,FL
Posts: 16
No, all the threads look good and intact...........the breech plug and threads in the barrel are spotless after cleanup........thats what I was thinking too, that there was something in the threads obstructing the breech plug from screwing in
kidvillain41300 is offline  
Old May 12, 2006, 01:57 PM   #4
cntryboy1289
Senior Member
 
Join Date: July 19, 2004
Location: Ms
Posts: 1,160
crud killer

I would advise you to use crud killer and a 50 caliber brush to scrub out the threads. Once your done, use a light to double check and see if there is anything left in the barrel. Then try to screw the breech plug back in. It should go back without any trouble, but if it doesn't, I would suggest that you have a buggered thread somewhere and the most likely place is at the rear of the threads.
cntryboy1289 is offline  
Old May 19, 2006, 09:52 PM   #5
mtnboomer
Senior Member
 
Join Date: July 9, 2004
Location: Oklahoma by birth. America by the grace of God.
Posts: 635
If you were using heavy loads in your gun you may have set the threads back due to the pressure. Always use an anti-seize lube compound on the breech plug threads when reassembling.
__________________
Quando Omni Flunkus Moritati (If all else fails - play dead!)

Support the Second Amendment. Join the NRA > http://www.nra.org <

Oklahoma State & Big 12 - #1 GO POKES!!!!!
mtnboomer is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:52 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06510 seconds with 7 queries