The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 5, 1999, 07:13 AM   #1
Hal
Senior Member
 
Join Date: October 9, 1998
Location: Ohio USA
Posts: 7,435
Ok, I had no reason to doubt it was anything other than what was advertised. The sign said new unfired, this was the third batch of brass I bought from the guy, but the first batch of .44 Special. The other stuff was .44 Mag. I primed 10 cases, belled the case mouth, charged them and seated the bullets. 5 went normal,3 didn't feel "right", as the bullets fell all the way into the case. ***? I resized one of the unprimed ones, and lo and behold, it went in hard all the way. I looked real close at the ones still in the bag, and sure enough, you can tell that they have been fired before. Not a big deal, but it kinda ticks me off enough that I had to vent about it here. I am a bit PO'ed about getting what appears to be once fired for the price of new, but more PO'ed that I didn't catch it right away. What's the best way to handel it? The guy sets up at the local shows. I have bought a fair amount of stuff from him in the past, stuff he has and the local shops don't carry, mainly brass and lead and Lee stuff. He seems like a straight shooter (no pun). Just tell him next time I'm at his table? Or should I go after him by opening a bag and pointing out that the stuff is obviously used, but cleaned and sorted. I'm not after any retribution or a refund, and I doubt if making a stink at his table would have any effect in the long run. Should I just use it as a learning experience? I know in the future, I will open and carefully look at every bag of brass I buy. It only takes a second, and maybe someone else in here may benifit. I bought 50 .44 Special and 100 .38 Special so it isn't like I stocked up for anything. Since I am going to load light, and the brass appears to be in decent shape,is marked R P, which I take to be Remington brass, I don't think I really got shafted. Even if it is once fired, it was cleaned and sorted, something the cheaper once fired usually isn't. I figure, at most, I overpaid less than $10.00, probably closer to $8.00, but it just galls me. I'm interested to hear how anybody here would handle it.
Hal is offline  
Old December 5, 1999, 10:20 AM   #2
HankL
Senior Member
 
Join Date: March 11, 1999
Location: The Sunny South
Posts: 2,174
Hal, I wouldn't hunt him down or anthing but the next time I saw him I would certainly bring it to his attention. He might have bought it thinking it was new brass. I would base my future relationship with this vendor on the outcome of your next meeting.
Hank
HankL is offline  
Old December 5, 1999, 11:21 AM   #3
Hal
Senior Member
 
Join Date: October 9, 1998
Location: Ohio USA
Posts: 7,435
HankL,
That's pretty much my thinking too. He seems like a decent sort that wouldn't purposely try to pull a fast one. Mainly I wanted to use my own stupidity as an example to TFL, to be careful when you buy components. I got took, but a lot of the fault was mine for letting it happen.

------------------
CCW for Ohio action site.
http://www.ofcc.net
Do what you C.A.N.

http://thematrix.acmecity.com/digital/237/cansite/can.html

Hal is offline  
Old December 5, 1999, 12:23 PM   #4
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,523
I agree with Hank's advice. But, I do wonder how you missed the fact that they were cleaned and not new from the gitgo. I'm not questioning your powers of observation, but there is always a huge difference in the luster of new vs. cleaned cases on the inside of the case even chemically cleaned ones. The reason I ask is that maybe they were new but not sized by the original mfg. I can't imagine that being the case, but maybe it is. Which company were they from?
Mal H is offline  
Old December 5, 1999, 04:56 PM   #5
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 2,641
Mal H. He said they were R/P. That's Remington. I've always resized and belled brand new brass as a matter of course. I've found brass from almost all the manufacturers to be loose, bent mouths and even without a primer flash hole. If that brass is in good shape, I would not get too bent about it. I'd tell the guy, but if he has been straight with you in the past, well maybe he got took.
I got a rifle in a trade, that was supposed to have been built by a well-known Tucson custom gun maker. We're talking trading a $1,400 drilling for a rifle of equal value.
Well, when I got home, I found that the rifle would not feed from the magazine, the trigger was a butchered up military, and after firing it as a single shotg, the bolt handle came off. Great rifle. Well, I live in Tucson, so I went to the purported gun maker. He said he did not make the gun, and that it was a forgery. Well it cost me several hundred dollars to make the gun right. At the next gun show, I saw the guy I got the gun from and told him what had happened. This was on a Saturday. He told me to bring in the receipts on my repairs and he would make it right. This I did, and he gave me $100 over my costs, just to cover something that might have been missed. Kudos to a gentleman and honest dealer. I sure look rifles over a lot closer now.
Paul B.
Paul B. is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05984 seconds with 7 queries