The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 26, 2006, 06:58 AM   #1
mjrodney
Senior Member
 
Join Date: March 5, 2006
Location: SW Florida
Posts: 435
Clays, 2.3 grains, 148g LSWC, .38 special, soft load? Too soft?

Newbie here again....

I loaded up a few .38 specials this morning, using 2.3 grains of Clays under a lubed 148 grain lead semi-wad cutter.

Does this sound like an adequate load?

I am amazed at just how little 2.3 grains of Clays powder is.

I put more salt on my food.
mjrodney is offline  
Old April 26, 2006, 09:46 AM   #2
Leftoverdj
Senior Member
 
Join Date: October 15, 2004
Posts: 934
Sounds mighty light to me, and that 148 grain LSWC does not sound right. It's possible that such a thing exists, but ordinarily 148 grains means a WC, and an SWC would be 150 or 158. 2.3 grains would be reasonable under a flush seated WC, but it's extremely light for a normal length SWC load.

It's extremely difficult to achieve uniformity with such a small load. Even the normal tolerance of plus or minus a tenth of a grain is nearly a 10% variation.
Leftoverdj is offline  
Old April 26, 2006, 11:17 AM   #3
mjrodney
Senior Member
 
Join Date: March 5, 2006
Location: SW Florida
Posts: 435
RE: Clays, 2.3 grains, 148g LSWC, .38 special, soft load? Too soft?

It seems light to me too, Leftoverdj, but that's based on a hunch and not real experience.

The Clay jar label calls for 2.5 grains, for a 148 LWC. I figured 10% below that for a mild load.

The bullets I bought from a local dealer, and the box calls them a 148g LSWC. They look like the standard double ended full wad cutter, with two lube grooves and the cannelure for crimping; but where they differ is on one end, where there is a small protrusion that is smaller than the bullet body. I guess that is what makes them a semi-wadcutter.

I weighed 50 of them on a digital scale and they came out to be 148.5 grains on the average.

These 50 I loaded this morning, and perhaps I need to load another 50 at the 2.5 grain mark, like it says on the Clay jar, before I go to the range this weekend.

Anyone else with Clays experience have more on this?
mjrodney is offline  
Old April 26, 2006, 11:35 AM   #4
rnovi
Senior Member
 
Join Date: July 10, 2005
Location: So. Cal.
Posts: 401
Ok, 2.3 grains IS A LIGHT LOAD. Also note: that's the way it's intended!

The 148gr wadcutters seat very deep in the case which helps to stabilize such a light load.

I use 3.0gr of Clays under a 125gr bullet in a 6" gp100. Recoil is non-existant, I get 1" groups at 7yards shooting fast DA shots. And it still clocks out at 950fps.

2.3 is light. That's pretty much the way it's intended. Bump to 2.5gr if you want...but it's still going to be soft.
__________________
Robert N.

"Remember, Eagles may soar but Weasels don't get sucked into jet engines!"
rnovi is offline  
Old April 26, 2006, 12:20 PM   #5
mjrodney
Senior Member
 
Join Date: March 5, 2006
Location: SW Florida
Posts: 435
RE: Clays, 2.3 grains, 148g LSWC, .38 special, soft load? Too soft?

Well then, friends, now maybe all will be well, after all.

These loads are for my recoil shy bride, who will be using a Ruger SP101 with a 3" barrel at the 7 yard mark.

If the bullet eventually reaches the paper and punches its way through, both of us will be happy.

I will plan on loading up 50 at the 2.5 mark, as well.

Thanks for the responses.
mjrodney is offline  
Old April 26, 2006, 12:31 PM   #6
sindiesel666
Senior Member
 
Join Date: November 17, 2004
Location: San Antonio
Posts: 270
I'm reading these posts and laughing like a maniac!!!
I once loaded some really light 38 spl loads, with 1.3-1.4 grains of Bullseye and some 158 grain lead SWCs. My range buddies where amazed that these loads actually pushed the bullet out of the barrel at all. I had no chrono, but I'd say they clocked around 400-500 fps. Can you say no recoil????

2.3 of Clays should definitely be nice out of a smaller frame revo like the SP 101. Pleasant to shoot and not intimidating for novice shooters.
sindiesel666 is offline  
Old April 26, 2006, 10:53 PM   #7
GrandpaDenny
Junior Member
 
Join Date: April 25, 2006
Location: West Michigan
Posts: 5
2.3 grains of Clay`s is the starting load for 148 Gr. full wad cutters in the Lee Modern Reloading book. Should work very well with your bullets and give little recoil to boot.

Keep the barrel clean and have fun. Light loads sometimes tend to lead up a barrel. Just keep an eye on it.
GrandpaDenny is offline  
Old April 27, 2006, 10:53 AM   #8
Steve 48
Member
 
Join Date: April 27, 2006
Posts: 59
I use 2.5 grains of Clays for all my 148gr wc. There very accurate and seem to be useful. Steve 48
Steve 48 is offline  
Old May 2, 2006, 04:17 PM   #9
btplus
Junior Member
 
Join Date: April 8, 2005
Posts: 5
I use Winchester Super Target in 1.8 gr.---148 gr hollow base wad cutters---and the federal primer. Set the bullet just below the case mouth. Shot by the thousands-popular PPC load here.
btplus is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07515 seconds with 7 queries