The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 25, 1999, 03:55 PM   #1
Abe Normal
Senior Member
 
Join Date: May 23, 1999
Location: Eastern North Carolina
Posts: 104
I was talking to a friend who also rolls his own and the use of "filler" to top off and hold the powder in place in a cartridge came up. He had only limited knowledge on the subject and I know how to spell "filler".

So, what is the poop on the use of a filler?

What sort of material can / should be used as a filler, for use in a gas opperated rifle?

Are commercial fillers the way to go, or is there a home brew recipe that's the hot ticket?

Is there a noticeable increase in accuracy that's worth the extra cost, trouble? Mess?
Or is this just another of those nebulous things that are done but will really only show there true worth if your shooting 600 to a 1000 yards with your match rifle?

Many thanks to those RKI's that choose to share their knowledge.


------------------
Abe

If everyone thought like me, I'd be a damn fool to think any different!

Abe Normal is offline  
Old October 25, 1999, 04:18 PM   #2
BigG
Senior Member
 
Join Date: May 19, 1999
Location: Atlanta, GA
Posts: 4,305
The only time I used filler was on top of reduced loads in rifle cartridges.

Example, 458 Win Mag loaded with 405 grain 45-70 lead bullets. Use about 30 grains of 3031 and put a tuft of dacron pillow stuffing (available in Walmart notions section) on top of powder to hold it in place back against the primer.

Without the filler, you get erratic ignition, perhaps a bullet lodged in the barrel. Hope this helps!

------------------
We don't have a chaplain here, but I don't view that as any major problem... You can rest assured that you will not go in that bag until I've said a few appropriate words over you
R. Lee Ermy as Sgt Major Haffner, from The Siege of Firebase Gloria

BigG is offline  
Old October 25, 1999, 07:23 PM   #3
bfoster
Senior Member
 
Join Date: October 13, 1998
Location: N. of Fords Switch, OK, USA
Posts: 297
If you are loading to reduced velocity in rifle cartridges, filler can help prevent pressure excursions if you insist on using pistol powders instead of powders like IMR SR 4759 & AA XMP 5744 which are designed for reduced loads. I know of one instance where a Marlin chambered in 45-70 was charged with a load of Unique which hasn't been published in the last 50 years. The shooter forgot to settle the powder toward the rear of the cartridge prior to igniting it. While there was a small lamination in the barrel steel, it is my opinion that the rifle failed in part due to a pressure wave: the case failed from the head toward the case neck, splitting the barrel along the way. The shooter sustained only minor injuries, the rifle became trash. Bob
bfoster is offline  
Old October 25, 1999, 10:44 PM   #4
TheOtherMikey
Senior Member
 
Join Date: October 16, 1999
Location: Surprise, Arizona, USA
Posts: 171
I have not yet used a filler personally but I have watched the filler-no filler debate for a couple of years on a number of boards.

Clearly, the camps are divided. The anti-filler folks say that using dacron, or corn meal fouls and eventually ruins the barrel. The pro-filler crowd says that using filler keeps the powder in place in a large capacity case, avoids dangerous pressure flucuations, and avoids poor accuracy due to bullet speed fluctuations. In fact, MD Smith's reloading board www.reloadammo.com provides different velocities based on "powder up" or "powder down" in the case.

For myself, I am leaning toward the pro-filler folks because I know small charges of fast burning powders in a large case (like a .45 Colt or a 45/70) can create a dangerous pressure situation. The largest case I currently reload is the .45 Long Colt, and I solve the problem by using a slower burning powder (2400) which fills up the case more.

Hope this helps, Mikey
TheOtherMikey is offline  
Old October 26, 1999, 11:38 PM   #5
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,518
As has been said, the benefit is keeping the powder back agaisnt the primer with reduced loads.

Among other things, oatmeal works.
Art Eatman is offline  
Old October 30, 1999, 07:01 PM   #6
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 2,633
Fillers work. I have a cast lead load for the 45-70 using the Gould 330 gr. hollow point bullet. Using a charge of IMR-4759, I fill the case to withing 1/8 inch of the neck, and seat the bullet. 2 inch groups are the norm with this load. Without the filler, the load shoots into 3 inches with almost 100 fps less veocity.
Paul B.
Paul B. is online now  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08227 seconds with 9 queries