The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 20, 1999, 04:12 PM   #1
Joe Portale
Senior Member
 
Join Date: June 8, 1999
Location: Tucson, Arizona Territory
Posts: 715
Howdy all,

I am looking for a suggested load for 30/30 with cast lead bullets. I am would like to participate in a steel target shoot offered by my club. I have loaded 30/30 for a while, but only metal jacket hunting loads. I looked in the Lee and Hodgdon books and didn't see anything for cast bullets. Oh, the targets will be typical mild steel out about 150 - 300 yards. Also, I will be using a 125 grain bullet.

Thank mucho!


------------------
Joe Portale
Sonoran Sidewinder
Tucson, Arizona territory

Joe Portale is offline  
Old September 20, 1999, 08:47 PM   #2
James K
Staff
 
Join Date: March 17, 1999
Posts: 18,652
Lyman puts out a manual with cast bullet loads. You will need a gas check or a very hard alloy for rifle loads.

Jim
James K is offline  
Old September 21, 1999, 12:56 AM   #3
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 2,534
Joe. Jim is right in what he said. I would like to add that I don't think a 125 gr. bullet has sufficient weight to knock down a steel target at 300 yards. I would go to at least 170 gr. or even heavier. Cast your bullets out of 10 pounds wheel weights, and one pound of linotype. This bullet will heat treat to a hardness of about 20 to 24 BHN.
Right now, I am tinkering with a 190 gr. bullet in the 30-30. I want to duplicate the old .303 Savage load, which had a 190 gr. Silvertip at 1950 FPS.
Old timers that I have talked to said it was a better killer on deer and elk than the
30-30 due to it's deeper penetration. It should have a lot on knockdown power on a steel target.
The first load I tried gave 2250 FPS on the chrony, but accuracy was terrible. I didn't want it going that fast anyway.
If you want to try some, I have bullets from 115 gr. to 200 gr. in .30 caliber in cast lead. E-mail me if you are interested.
Paul B.
Paul B. is offline  
Old September 26, 1999, 03:12 PM   #4
Reddog
Member
 
Join Date: August 1, 1999
Posts: 56
Joe,I've been shooting lead bullets in my 30/30 for about 15 years. I use the Lee 180 gr. rn/flat nose gas check mold. I have three different loads I use. 25 gr. BLC-2, 15 gr. 2400 and 21.5 gr. 4198. I also put a pea sized ball of Dacron on top the powder. I have a Ted Williams Sears 30/30 and a son with a Win. 94, and have had good luck in both guns. In my opinion, lead is the only way to go with a 30/30. Like Paul says, use heavier bullets. Reddog
Reddog is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07867 seconds with 7 queries