The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old April 1, 2006, 06:09 PM   #1
wacki
Senior Member
 
Join Date: December 19, 2004
Location: Moving out of Indiana
Posts: 426
366 hornady for $50, should I buy it?

A guy in a trailer is offering me one of these for $50. It's not stolen.



I've looked at it and the tubes are so old they are almost opaque yellow. It's red so it has to be less than 30 years old. The claw needs to be replaced or at minimum bent as when I pull the handle the plate doesn't always rotate. The tall skinny tube for the primer tray is missing.

Other than that it seems fine but I've never used one so I don't know. Any advice?
wacki is offline  
Old April 1, 2006, 08:00 PM   #2
WIN71
Senior Member
 
Join Date: March 28, 2005
Posts: 649
thief......thief !!!

He may not have stolen it but you are !!!!!!!
WIN71 is offline  
Old April 1, 2006, 09:45 PM   #3
wacki
Senior Member
 
Join Date: December 19, 2004
Location: Moving out of Indiana
Posts: 426
Quote:
thief......thief !!!
He may not have stolen it but you are !!!!!!!
This may be true but please tell me what I should look for to make sure I'm not getting "ripped off". I've never used one so for all I know it's completely broken or the gunpowder/shot disperser isn't working right and will cost an arm and a leg to fix. Best way to test it? Should I fill it with sand or something cuz I can't test it with gunpowder.

Hell it's only $50 so it's worth the risk I guess.
wacki is offline  
Old April 1, 2006, 10:39 PM   #4
WIN71
Senior Member
 
Join Date: March 28, 2005
Posts: 649
ok

What I ment by my comment was that is about a $450.00 press new so unless one of the castings is crasked it's a steel. I bought one about 4 years ago. Originally they were produced by Pacific. Although mine was sold as Hornady some of the parts are still marked Pacific. If it were me I would put some empty fired hulls in and work the handle. You'll need to clamp it to something semi solid. Go slow and watch everything that moves. Look for excessive springing, bending or cracks opening up. Each stroke should move the charging bar one way then on the next stroke the other way. There is a shut of lever at each end of the bar that controls the flow/no flow of both powder or shot. It doesn't matter which way they are turned for a function test as the bar moves either way or it should if working properly. The linkage for this movement is in the back of the press and fairly straight forward. If you want to inspect the charging bar, housing, and shot/powder tubes you can loosen the only knurled screw on the right side of the casting that holds the bar housing. It's right between the shot/powder tubes and below. Twist a little and the whole assembly will come out of the linkage in the back and you can strip it down to all the individule parts. I forget which one but either the powder or shot bushing will probably fall out.
If after doing all this and you find nothing broken, cracked, or missing you should be fine. That finger you refer to that advances the shell holder is an easy fix. It's made to lift up so you can cycle the machine without advancing the hulls. Handy when something goes wrong. If this press has sat around a long time unbolt the large nut in the center of the shell holder, lift out the plate and make sure there arn't old spent primers, shot or any other foreign material between the plate and casting. It will bind everything up if it's there.
Don't worry about the drop tube for the primers, that's easily replaced.
Other than that, if it has all the parts the one in your picture has you should be ok.

Ron
P.S. Sorry about the "thief" comment. If everything turns out ok on this press deal for $50.00 you"ll be promoted to used car salesman.........!!
WIN71 is offline  
Old April 1, 2006, 11:33 PM   #5
Ruger4570
Senior Member
 
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
I would think that if for some reason you had to totally rebuild it (which is doubtful) you would still be bucks up
Ruger4570 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:23 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06256 seconds with 7 queries