The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 21, 1999, 10:13 PM   #1
GLV
Junior member
 
Join Date: October 14, 1998
Location: Logansport, IN, USA
Posts: 217
Like something for the 150gr flat base bullet
using IMR powder. I know I have many 'loading for the Garand' articles -- somewhere! If someone has the issue number of Handloader when they did an article on the Garand, please post it. Thanks, GLV
GLV is offline  
Old June 21, 1999, 11:18 PM   #2
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,031
I load 52.5 gr of IMR 4064 in my bolt action. I'd venture that to be down around 47,000 psi, around 48.0 or 49.0 gr. would work.

The key is the 47,000 psi, for best cycling. The pressure at the gas port is supposed to be around 2,000 psi...

While I have shot my max loads in my Garand, I have read that this is a long-term no-no, which makes sense. No point in slamming it around during cycling.

Some others may well have some 4895 loads, too...

Good luck, Art
Art Eatman is offline  
Old June 22, 1999, 02:11 PM   #3
Joefo
Senior Member
 
Join Date: March 22, 1999
Location: NY
Posts: 165
I use 45 gr. of 4895 in my Garand. It shoots real nice. Very accurate. I have scored pretty high with these loads. I'm going to try some Varget and see how that works in a Garand. It (Varget) works real nice in an AR-15.
Joefo is offline  
Old June 25, 1999, 09:38 PM   #4
GLV
Junior member
 
Join Date: October 14, 1998
Location: Logansport, IN, USA
Posts: 217
Art, Joefo, thanks for the information. GLV
GLV is offline  
Old June 26, 1999, 08:25 AM   #5
Patrick Graham
Junior member
 
Join Date: January 18, 1999
Location: Kokomo, Indiana USA
Posts: 674
From the NRA publication "The M1 Rifle"
Approxmate Mil duplication loads for 30-06.

I don't know how how hot these will be but they seem kinda light in the 4064 department.

These loads are for Commerical Cases
They recommend dropping these charges back 1.5 grains for mil cases.

147/150 gr Bullet
IMR3031 = 48gr
IMR4895 = 49gr
IMR4064 = 50gr

165/168 gr Bullet
IMR4895 = 47gr
IMR4064 = 48gr

173/175 gr Bullet
IMR4895 = 46gr
IMR4064 = 47gr

180 gr Bullet
IMR4895 = 43gr

There are many other powders listed, these are just the IMR loads.

Here's more to digest :-)
From an old Dupont Handloaders guide.

150 gr Bullet
IMR3031 = 49.5gr
IMR4895 = 49.5gr
IMR4064 = 52gr

180 gr Bullet
IMR3031 = 44.5gr
IMR4895 = 43.5gr
IMR4064 = 49.5gr

Here's even more yet =:-O
from the Serria Rifle Reloading manual, 3rd Edition. (My Favorite)

150 gr Bullet
..........Min-------Max
IMR3031 = 44.4gr----49.5
IMR4895 = 44.4gr----50.4
IMR4064 = 46.5gr----52.8

165 gr Bullet
..........Min-------Max
IMR3031 = 40.5gr----46.1
IMR4895 = 41.6gr----47.8
IMR4064 = 42.8gr----49.6

[This message has been edited by Patrick Graham (edited June 26, 1999).]
Patrick Graham is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06819 seconds with 9 queries