The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 3, 1998, 08:35 AM   #1
TheWalls
Junior Member
 
Join Date: December 2, 1998
Location: Coffeyville,KS
Posts: 4
How good are they? Will they work in my RCBS press. They advertise that you don't need to use lube. Will this reduce the life of the die.
Also would like to here comments on the Lee perfect powder measure. I've heard lots of good things about them. Are they consistent enough for rifle reloading?
TheWalls is offline  
Old December 3, 1998, 10:40 AM   #2
fal308
Staff Alumnus
 
Join Date: October 12, 1998
Location: Missouri
Posts: 1,986
One of my powder measures is the Perfect. My consistency isn't the greatest. My Pacific is better. My 45/70 load measures between about 32 gr. to around 33 gr.. You've got to get the sideplate screwed down to the correct tension (I did mine by trial and error). Too tight and no flow, too loose and powder spills out the side. The difference is not very large between too tight, just right, and too loose.
fal308 is offline  
Old December 3, 1998, 02:28 PM   #3
Fred
Senior Member
 
Join Date: November 3, 1998
Location: CA
Posts: 465
The Lee collet dies are neck-size only, that's why you don't really need case lube when sizing brass. As a practical matter, I have a set that I use for a .22-250 and do occasionally put just a very small amount of case lube on my brass simply because I remember an article that said it was a good idea to do so. Othere than that, I usually just run the brass into the sizing die with nothing on it. I don't think it hurts anything, nor do I think it will shorten the life of the dies as long as you clean any accumulated dirt, grit, etc., out of the dies every so often. Hope that helps.
Fred is offline  
Old December 3, 1998, 02:31 PM   #4
Fred
Senior Member
 
Join Date: November 3, 1998
Location: CA
Posts: 465
Sorry, forgot to answer your question about the RCBS press. Yes, the Lee dies will work in the RCBS press without difficulty as they share the same thread dimensions as RCBS dies.
Fred is offline  
Old December 10, 1998, 11:18 PM   #5
Contender
Senior Member
 
Join Date: December 10, 1998
Location: NY
Posts: 680
My experience with the Lee Collet die was one of an oversized mandrel in the caliber I was using. This resulted in the neck inside diameter to be too large for the bullet. However, Either you can spin the mandrel in a lathe or drill press to remove small amounts of material or return a couple of fired cases and a bullet or two with the die to Lee and they will make the adjustment. As far as the Perfect powder measure, I too have had trouble with adjusting the drum tension forget fine powders especially the ball type they will bind it up very nicely or dump more powder on your bench than in the case. I really liked the graduated adjustable cavity though. I wish other measures had one like it without paying a premium for it.
Contender is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:51 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06386 seconds with 9 queries