The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old March 14, 2006, 01:01 AM   #1
Hello123
Senior Member
 
Join Date: February 21, 2005
Posts: 571
Torque specs for Savage?

When the stock is removed from a Savage to adjust an accutrigger and put back on the gun, how tight should the action? screws be retightened?
Hello123 is offline  
Old March 14, 2006, 09:35 AM   #2
cntryboy1289
Senior Member
 
Join Date: July 19, 2004
Location: Ms
Posts: 1,160
guess only but

I would think around 65 in/lbs.
cntryboy1289 is offline  
Old March 14, 2006, 11:48 AM   #3
DnPRK
Senior Member
 
Join Date: August 24, 2001
Location: LC, Ca
Posts: 1,771
Injection-molded plastic, laminated wood or hardwood stock?

Even the Savage stocks with pillars tend to crush a bit when the screws are torqued because the pillars are short. If the forward screw cavity crushes enough, it can intrude into the receiver and bind the bolt.
DnPRK is offline  
Old March 14, 2006, 03:04 PM   #4
Hello123
Senior Member
 
Join Date: February 21, 2005
Posts: 571
Hardwood (walnut) stock. Look forward to your answer, thanks.
Hello123 is offline  
Old March 14, 2006, 04:41 PM   #5
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,395
Cntryboy1289 was a tad high for wood. The numbers he gave are those recommended by Choate for their Ultimate Sniper and Ultimate Varmint stocks. They supply hardened socket head screws for the purpose. From Choate's information below:

"We furnish you with a new set of receiver screws. They are grade
8 Tool and Die quality hex socket machine screws. They should be
torqued to 55 to 65 inch pounds (NOT FOOT POUNDS) of torque.
Without the aluminum bedding pillars this would not be possible. Try
this in a wood or plastic stock and you will split it wide open. This high
torque assures that your rifle and new Choate stock are bolted together
until you want them apart.


For wood without aluminum pillars I think you will wind up in the 15 in-lb range. You might get as high as 20 before unhardened screws start to tear up, but you will be loading the wood with enough stress that moisture and temperature changes could start a crack. And as Choate advised, don't get a foot-pound torque wrench confused with an inch-pound wrench, or you will be torquing 12 times harder than you think! I've measured 8-12 in-lbs on a number of conventionally stocked guns I've disassembled, with only an occassional tighter one.

For maximum accuracy you can put aluminum or stainless pillars into the wood stock, get hardened screws, then apply significantly more torque.

Nick
Unclenick is offline  
Old March 15, 2006, 02:37 PM   #6
mgdavis
Senior Member
 
Join Date: June 24, 2004
Location: Western Washington
Posts: 397
+1 to UncleNick. If you don't have a torque wrench that does in-lbs, 12-15 in-lbs is just about hand snug with a screwdriver IIRC.
__________________
Since the internet is anonymous, I'm really good looking too.
mgdavis is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:49 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07176 seconds with 7 queries