The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old March 14, 2000, 02:06 AM   #1
Don Parsley
Member
 
Join Date: January 27, 2000
Posts: 17
As far as safely shooting lead bullets and having a fully supported chamber, what is the best and cheapest way to go in obtaining a new barrel? Any suggestions for a Glock 23 in 40S+W

[This message has been edited by Don Parsley (edited March 14, 2000).]
Don Parsley is offline  
Old March 14, 2000, 05:36 AM   #2
bk40
Senior Member
 
Join Date: January 12, 1999
Location: Mississippi
Posts: 1,004
Not the cheapest way to go, but I would choose either a BarSto or KKM Precision barrel. I've got Glocks (and other pistols) with these 2 barrels in them and they are accurate and worth the extra $$ IMO.

------------------
BKs Pistol Pages
bk40 is offline  
Old March 14, 2000, 09:31 PM   #3
George Stringer
Staff Alumnus
 
Join Date: October 12, 1998
Location: Earlington KY
Posts: 2,299
Don, you'd have to go pretty far to beat the two recommended above but Brownells www.brownells.com sells replacement barrels that aren't quite as expensive. George
George Stringer is offline  
Old March 14, 2000, 10:37 PM   #4
Don Parsley
Member
 
Join Date: January 27, 2000
Posts: 17
George, thanks for the info. I have reloaded thousands of rounds of 40 and shot them out of my 23,but I kept the barrel spotless with an Outers foul-out. The problem that really disturbs me is the non-supported chamber. Looking over brass I have used,there are some very serious bulges and rings that could have hurt the pistol or worse. P.S. I'm new to this e-mail thing so forgive any mistakes I make. Thanks again.Also thanks to bk40,some really good gun pages!!

[This message has been edited by Don Parsley (edited March 14, 2000).]
Don Parsley is offline  
Old March 15, 2000, 03:11 PM   #5
Tom B
Senior Member
 
Join Date: February 16, 1999
Location: GA
Posts: 1,836
I put a KKM drop in barrel in my G23 and it worked great with much better accuracy. Do a "search" here on aftermarket barrels or just barrels and you will get much info and many threads.
Tom B is offline  
Old March 16, 2000, 12:40 PM   #6
nwgunman
Senior Member
 
Join Date: July 16, 1999
Location: Olympia, WA
Posts: 312
I put a KKM barrel in one g23 and a Jarvis barrel in the other m23. I like the KKM a little better. It seems like the chamber on the Jarvis is just a tad too tight, whereas the KKM will keep on chugging even after a couple of hundred rounds. I really like the way these barrels don't bulge the brass like the factory barrels do. I don't shoot lead at all in my .40s so can't comment on that.
nwgunman is offline  
Old March 21, 2000, 12:26 AM   #7
Pooch
Member
 
Join Date: March 3, 2000
Posts: 38
Ive shot thousands of hard cast (linotype, 22 brinell or better) out of my 23 at mid power level, I have yet to have any incident nor after about 4 reloads any smiley faces on my brass. I keep my barrel clean, but the key is HARD cast bullets only and uniformly sized ones at that. If you use the soft swagged lead bullets, you better clean your barrel with every mag change or you might KB. With linotype, I shoot a match no problem 150 200 rounds, Im sure I could do it again but I clean the barrel. Now that there are good plated bullets (I dont like raniers) Ie west coast and berries, Im not loading lead, but one day you might need to, so make it hard lead and your good to go! If someone tells you Glocks blow up with lead, aske them what guns and what kind of lead they have loaded, most likely they are a parrot repeating what someone told them and they dont know swagged from cast. But if you must and you feel better, get a new aftermarket barrel,(the two above are great) but if you shoot soft swaged lead, your gonna blow that one just as easy, becasue the KEY is hard cast lead, not barrels and if you load to max capicity your gonna start to come up against the partially unsupported and lose Glock barrel, just back off, 3/4 level will often get you to major in most calibers. I have shot 9,40 & 10mm linotype in Glocks, this is my experience, not hearsay!
Pooch is offline  
Old March 21, 2000, 10:59 PM   #8
WalterGAII
Junior member
 
Join Date: November 7, 1999
Posts: 1,516
Try JR, at Lonewolf Distributors. They sell Federal barrels of Glocks for $89. They're not the best, but they work fine and are at least as accurate as your Glock factory barrel.

Brownell's sells the Briley, Bar-Sto and KKM drop in barrels for the same price, $148. Just open a Brownell's account online, answering the question regarding being in "a related business that doesn't require an FFL" in the affirmative. You'll instantly be given Brownell's trade discounts.
WalterGAII is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07700 seconds with 7 queries