The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old January 7, 2006, 12:09 PM   #1
Idlechater
Member
 
Join Date: January 4, 2006
Posts: 37
Glass Bed or Oil Stock - Which First

Hey Gang:

Well I have stripped all the old finish off of my M77 stock. I am wondering if I should glass the action before applying the oil finish to the stock, or do the oil finish first. My gut is telling me to do the glassing first and then apply the finish, but I just want to check and be sure.

Thanks.

Last edited by Idlechater; January 10, 2006 at 01:04 AM.
Idlechater is offline  
Old January 7, 2006, 02:22 PM   #2
Toney
Senior Member
 
Join Date: August 17, 2005
Location: Stillwater Oklahoma
Posts: 651
Bed first, it will stick better to the wood than the oil
Toney is offline  
Old January 8, 2006, 03:20 PM   #3
Tom2
Senior Member
 
Join Date: June 23, 2004
Location: Ohio
Posts: 5,647
agreed

Glass bed is basically epoxy. I have found it will not stick very well or at all, to milsurp stocks that have had oil/grease penetration. Of course, if you don't get the finish inside of the cutouts that you intend to bed, that might not be a problem.
Tom2 is offline  
Old January 8, 2006, 07:18 PM   #4
Harry Bonar
Senior Member
 
Join Date: December 5, 2004
Location: In the Vincent, Ohio general area.
Posts: 1,804
glass or oil

Dear Shooter:
Right on guys! Get your Dremel tool out and with a round burr cut SOME area out, especially behind the recoil shoulder, rough up things up a bit as suggested - get some Brownells "steel bed" and their new spray-on release agent like I just did and have at it as already suggested.
DO NOT, do not, bed beyond the face of that action - do not bed the barrel channel! You will, after you're done relieve the bbl just in front of the action face. You want that bbl. floated cardboard like all the way out! It'll shoot!
I like "Tru-Oil" as a finish.
Harry B.
Harry Bonar is offline  
Old January 9, 2006, 08:58 PM   #5
hIPSHOT33
Senior Member
 
Join Date: October 24, 2005
Location: ETNA CA. IN THE REAL NORTHERN CALIFORNIA
Posts: 120
I would say ,Bed firest . I have had good luck with Brownell's Acra-Glass . I agree with Herry B . Stay behind the face of the actino . I use one layer of electrical tape from the face of the action out to the End of the stock . That gives me a good free flote on the barrel .
hIPSHOT33 is offline  
Old January 31, 2006, 12:44 PM   #6
DiplomaticBlackHawk
Member
 
Join Date: August 2, 2005
Posts: 87
someone here might smack me upside the head and please do if need be lol but I have tried a lot of stuff , cheap , ecpensive , top of the line , the list goes on. But I bought a mil-surplus 30-06 and used a different , maybe taboo method.I was doing some body work on my once all original , mint 68 caddy convertible after it was STOLEN when I was at the sheriff's office getting my CCL , trust me I will stop here PM me in a day or so once i've calmed down again from talkin about it .Well I desided IF i had to fill anything I would only use duraglass , not any bondo crap , all I use on anything besides lead , but any way I used it to bed the rifle and it work better than anything i have ever use , took a little more effort but ended up making a hell of a gun. Buy one cheap as heck and try it , might make a fun project.
DiplomaticBlackHawk is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:06 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07308 seconds with 7 queries