The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 21, 1999, 03:02 AM   #1
Natty Bumpo
Junior Member
 
Join Date: September 30, 1999
Posts: 9
A Ruger Security Six is dependable, but its trigger pull is the pitts. There isn't much you can do about the "mile-long" travel, but is there any way to lighten it up and smooth it out?

As always, Thanks for the help.

------------------
><>
Natty Bumpo is offline  
Old November 21, 1999, 08:24 AM   #2
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 16,594
I bought a Clark adjustable mainspring (from Gil Hebard) and installed that in my Security Six. The mainspring guiderod was threaded and a nut installed on the end. By moving the nut, you adjusted the weight.

On the trigger, I slowly polished the sear, hammer and trigger on a hard arkansas. I also lightly polished the pawl (hand) and the cylinder stop. The mainspring guiderod (or is it called the hammer strut) which engages the hammer (the round part) was also polished. My polishing method was to lay the piece on the arkansas, keep it level and moving it slowly across the well oiled surface of the stone. This was done several times and the part refitted. A lot of testing (requiring reassembly) was required, and then it was disassembled and polished some more. The whole process was repeated until I was happy (and safety of the working mechanism wasn't compromised).

------------------
Vigilantibus et non dormientibus jura subveniunt

4V50 Gary is offline  
Old November 21, 1999, 08:49 AM   #3
George Stringer
Staff Alumnus
 
Join Date: October 12, 1998
Location: Earlington KY
Posts: 2,299
Natty, the Clark spring unit is a good one but getting a light smooth DA pull on a revolver involves stoning/polishing 9 different areas. This is best left to a smith. George
George Stringer is offline  
Old November 21, 1999, 11:21 AM   #4
Dave McC
Staff In Memoriam
 
Join Date: October 13, 1999
Location: Columbia, Md, USA
Posts: 8,812
Never was too fond of the spring replacement idea, but a Security Six I had years ago responded well to complete dissasembly, polishing all the wear marks out with a Dremel with a felt tip and Jeweler's rouge, lubing with Gunslick, wiping off all the Gunslick with a paper towel or clean lint free cloth and reassembly.

For good DA work, a light trigger is nice, but a smooth,clean pull's essential...
Dave McC is offline  
Old November 21, 1999, 09:32 PM   #5
Robert Foote
Senior Member
 
Join Date: December 31, 1998
Posts: 623
I went through a Ruger armorer's school some years back and have Kunhausen's book but never have felt comfortable doing much custom trigger work. If anyone knows of someone who does these and GPs exceptionally well I would be interested in a referral. I have a GP that has an absolutely beautiful trigger job--but the smith is no longer in business...

------------------
Robert Foote is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:26 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07533 seconds with 7 queries