Dan Wesson M15 357 Magnum parts/pieces search

Sir William · October 11, 2005, 04:43 AM

I am seeking a inner barrel for the 2" and 4" barrel shrouds in blue and their nuts. I am also seeking complete barrels, shrouds and nuts for 8" and 10" in blue. 357 Magnum. Sight insert colour is not an issue. Spare nut wrenches and Pachmayrs would be good too. I have tried Midway and Brownells. No luck. Any suggestions/sources/sites appreciated. TIA

Peter M. Eick · October 11, 2005, 02:10 PM

You could always just call Dan Wesson arms in Norwich and buy them new....

Michaelm45 · October 11, 2005, 04:32 PM

Did you give Numrich a try?
http://www.e-gunparts.com/model.asp?idDept=60

Sir William · October 11, 2005, 06:15 PM

Numrich has M-12 parts but, no barrels for the M-15. I will try Dan Wesson/CZ.

Harry Bonar · October 16, 2005, 04:18 PM

Dear Shooter:
You may need to order Douglas bbl' blanks, turn them down, thread them for the tensioned bbl they have and go that route!
Just an aside; when you set up your bbl, shoot about a cylinder full and then, while the liner is hot, tension it again. They are very accurate revolvers.
Be careful, in a combat situation going up a staircase that you've polished the rear flange so the case rim doesn't catch in rotation; try it and you'll see what I mean.
Harry B.

molonlabe · October 16, 2005, 05:24 PM

Try this
Post 5

http://www.thefiringline.com/forums/...&highlight=Dan

MADISON · October 25, 2005, 02:16 PM

Have you tried:
www.danwesson.com

mdw442 · December 11, 2005, 05:33 PM

Definitely go direct to danwesson.com I used to rebuild a lot of the Dan Wesson .357s and .44 Magnums and the one thing I learned is these models are always being updated and improved. The barrel tool kit is a prime example. The one they sell now is fantastic compared to the ones sold only a couple years ago.

The only one thing I dislike on the DW site is their flourescent sights. In my opinion, they are garbage. They are not true flourescents and difficult to see in low light conditions. I liked substituting other brands of Flourescents instead. Much better.

October 11, 2005, 04:43 AM	#1
Sir William Senior Member Join Date: October 13, 2004 Posts: 3,261	Dan Wesson M15 357 Magnum parts/pieces search I am seeking a inner barrel for the 2" and 4" barrel shrouds in blue and their nuts. I am also seeking complete barrels, shrouds and nuts for 8" and 10" in blue. 357 Magnum. Sight insert colour is not an issue. Spare nut wrenches and Pachmayrs would be good too. I have tried Midway and Brownells. No luck. Any suggestions/sources/sites appreciated. TIA

October 11, 2005, 02:10 PM	#2
Peter M. Eick Senior Member Join Date: August 4, 1999 Location: Houston, Texas Posts: 2,567	You could always just call Dan Wesson arms in Norwich and buy them new.... __________________ 10mm and 357sig, the best things to come along since the 38 super!

October 16, 2005, 04:18 PM	#5
Harry Bonar Senior Member Join Date: December 5, 2004 Location: In the Vincent, Ohio general area. Posts: 1,804	Dan Wesson parts Dear Shooter: You may need to order Douglas bbl' blanks, turn them down, thread them for the tensioned bbl they have and go that route! Just an aside; when you set up your bbl, shoot about a cylinder full and then, while the liner is hot, tension it again. They are very accurate revolvers. Be careful, in a combat situation going up a staircase that you've polished the rear flange so the case rim doesn't catch in rotation; try it and you'll see what I mean. Harry B.

October 16, 2005, 05:24 PM	#6
molonlabe Senior Member Join Date: May 17, 2004 Location: MD Posts: 296	Try this Post 5 http://www.thefiringline.com/forums/...&highlight=Dan __________________ The United States Constitution © 1791. All Rights Reserved. I Don't want you in here period...Patricia Konie NOLA 2005

October 25, 2005, 02:16 PM	#7
MADISON Senior Member Join Date: January 1, 2000 Location: Roanoke, Virginia Posts: 2,678	Dan Wesson parts Have you tried: www.danwesson.com

October 11, 2005, 04:32 PM	#3
Michaelm45 Senior Member Join Date: October 28, 2004 Location: NV Posts: 215	Did you give Numrich a try? http://www.e-gunparts.com/model.asp?idDept=60

October 11, 2005, 06:15 PM	#4
Sir William Senior Member Join Date: October 13, 2004 Posts: 3,261	Numrich has M-12 parts but, no barrels for the M-15. I will try Dan Wesson/CZ.

December 11, 2005, 05:33 PM	#8
mdw442 Junior Member Join Date: December 9, 2005 Posts: 8	Definitely go direct to danwesson.com I used to rebuild a lot of the Dan Wesson .357s and .44 Magnums and the one thing I learned is these models are always being updated and improved. The barrel tool kit is a prime example. The one they sell now is fantastic compared to the ones sold only a couple years ago. The only one thing I dislike on the DW site is their flourescent sights. In my opinion, they are garbage. They are not true flourescents and difficult to see in low light conditions. I liked substituting other brands of Flourescents instead. Much better.