The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old September 19, 2005, 09:56 PM   #1
zebrajeb
Member
 
Join Date: September 19, 2005
Location: Reno, NV
Posts: 53
Mossberg Stainless Pump?

New on this site but enjoy reading the posts.

I've recently acquired a Mossberg 12 ga. which appears to be all stainless steel, including what looks like a factory stainless heat shield. 18 inch barrel and extended magazine. Anyone know anything about this shotgun, when it was made, etc.?

I've owned an 870 Marine and seen the newer Mossberg with Marinecote but not a stainless one before.

Thanks

JEB

Last edited by zebrajeb; September 19, 2005 at 11:54 PM.
zebrajeb is offline  
Old September 20, 2005, 10:55 AM   #2
CaCrusin
Senior Member
 
Join Date: December 15, 2004
Location: Paso Robles, CA
Posts: 115
Marinecoate is all they list. The receivers are all made of aluminum. It is either marinecoate or a refinish job.
__________________
Ca Crusin
_________________________

SI VIS PACEM PARA BELLUM
_________________________
www.knoxx.com
CaCrusin is offline  
Old September 20, 2005, 07:59 PM   #3
zebrajeb
Member
 
Join Date: September 19, 2005
Location: Reno, NV
Posts: 53
Nope, not Marinecote - definitely since I had it next to a Mossberg with Marinecote. Receiver is definitely not aluminium but solid. It really appears to be stainless and not refinished.

John
zebrajeb is offline  
Old September 21, 2005, 12:16 AM   #4
liliysdad
Senior Member
 
Join Date: June 7, 2004
Posts: 1,144
I seriously doubt its a stainless gun.....in fact, id be willing to bet its not
liliysdad is offline  
Old September 21, 2005, 05:07 PM   #5
RevolverLover
Senior Member
 
Join Date: November 22, 2004
Posts: 1,682
To my knowledge Mossberg only used aluminum recievers. Maybe its a Marinecote that has been polished?
RevolverLover is offline  
Old September 21, 2005, 07:28 PM   #6
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 6,773
There was an older Mossberg called The Model 500 Mariner.
It had something called a "Marinecote" finish that looked like stainless, but was more rust resistant than stainless.

Apparently the earlier Marinecote looked different than the current version of Marinecote.

The only other thing I can think of, is someone had the gun hard chrome plated.

With a used gun, you have no idea what a previous owner may have done to it.
Dfariswheel is offline  
Old September 21, 2005, 07:35 PM   #7
MillCreek
Senior Member
 
Join Date: December 30, 2004
Location: Snohomish County, Washington USA
Posts: 281
Let me say right now that if Mossberg made a 590 in stainless, I would buy one in a heartbeat.
__________________
Regards,

MillCreek
Snohomish County, Washington USA
MillCreek is offline  
Old September 21, 2005, 08:08 PM   #8
zebrajeb
Member
 
Join Date: September 19, 2005
Location: Reno, NV
Posts: 53
Well, I appreciate the suggestions. Feeling like an idiot, I put a magnet to the receiver and it is definitely not steel! Learn something new every day! However, receiver is polished, fairly bright (not mirror) and smooth. I honestly don't know what has been done to it.

If Mossberg made an earlier version of the Marinecote, as Dfariswheel suggested, this might be one. The magazine cap and sling swival are different than the current production Mainecote shotgun and the finish on barrel is much smoother - more like a brushed stainless. This shotgun is also a little shorter overall as well. Barrel is 18 inches with a stainless (unless coated) heat shield. It all looks factory but I'm not an expert.

I'm more familiar with the Remington shotguns (once had a Marine and wish I'd kept it). This one just fit well and I wanted something like this. (My other shotgun is an FN Police with removeable chokes.)

Appreciate the information, suggestions & not calling me an idiot.

John
zebrajeb is offline  
Old September 22, 2005, 10:31 AM   #9
CaCrusin
Senior Member
 
Join Date: December 15, 2004
Location: Paso Robles, CA
Posts: 115
Not an Idiot!

It is no disgrace to be ignorant on a subject. It is a disgrace to remain so when the opportunity presents itself for enlightenment. You have done well.

You are not an idiot.
__________________
Ca Crusin
_________________________

SI VIS PACEM PARA BELLUM
_________________________
www.knoxx.com
CaCrusin is offline  
Old September 27, 2005, 11:34 PM   #10
warthog5
Member
 
Join Date: September 27, 2005
Posts: 15
The only one in this class that I'm aware of is the
Winchester 1300 Coastal. It does have a stainless barrel that is then chrome plated.

Mine just came in today. It also is a lighter weight SG that other's in it's class.



The SpecOps stock came in today too.



They are not near as cheap as the one's you will find at the box store's. Fact is you will not find much about them on the net, except on Winchester's site.
I got a decent price on this one. $513
warthog5 is offline  
Old September 28, 2005, 12:39 AM   #11
gig-a-hertz
Junior Member
 
Join Date: September 27, 2005
Posts: 3
Howdy.

I have a 500 Mariner that looks exactly like the inguirer describes. It is an early one as I have had it for about 15 years. It is a shinier gun than the current matte finished Mariners. Those are like bead-blasted?
The reciever is a polished aluminum & the rest is electroless nickle ie: Marinecoat. It does have the factory heatshield. It came with the 4-round Speedfeed stock also.

I also have the Winchester 1300 Marine Defender.
It is chromed on barrel & mag-tube, but with polished aluminum reciever. The newer ones of these seem to be like the one pictured with the matte-black reciever.

Then there is the Remington 870 Marine Magnum.
It is more like the Mossberg in finish & I have seen more of those that have the bead-blasted dullness. Mine is not like that. It is more shiny.

Of the 3....the Mossberg is a treat to shoot. The Remington is decent. The Winchester is the most miserable recoil-wise of any riot gun I ever shot.
I have used same handloads in 00 buck & home-cast slugs in all of them. The winchester is pretty rough on me.
(as one guy noted..it is the lightest)
All are rynite stocks with 18.5" barrels.

John
gig-a-hertz is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08172 seconds with 7 queries