The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old September 15, 1999, 08:23 PM   #1
Big Bunny
Senior Member
 
Join Date: August 9, 1999
Location: New South Wales - Australia
Posts: 605
Opinions please on this 'recommended' knife sharpener.
Standard or diamond versions ?
Operation/ease of use/durability and satisfied customers ?

Lets hear it...

------------------
***Big Bunny***
Big Bunny is offline  
Old September 15, 1999, 08:53 PM   #2
ga41
Member
 
Join Date: February 18, 1999
Location: thomaston,ga USA
Posts: 17
I like my diamond sharpener. The only problem I've had was that I broke the plastic end off one of my stones once. Seems like someone said there was a better setup , I just don't remember where or who. Maybe we'll hear from them.

[This message has been edited by ga41 (edited September 15, 1999).]
ga41 is offline  
Old September 16, 1999, 04:54 AM   #3
Rich Lucibella
Staff
 
Join Date: October 6, 1998
Location: South Florida
Posts: 10,156
I own the Lansky setup and am completely underwhelmed. The clamp does not assure reproducible angle with many knives; the edge angle, by geometric necessity, changes from point of attachement out to each side; and the unit is worthless for any blade length over about 4".

Go with the Spyderco Sharpmaker. Add their diamond sleeves and your knives will thank you.
Rich

[This message has been edited by Rich Lucibella (edited September 16, 1999).]
Rich Lucibella is offline  
Old September 18, 1999, 12:17 AM   #4
Nakano
Member
 
Join Date: March 1, 1999
Location: USA
Posts: 72
Rich, I' ve found that the angles do vary sometimes but not all the time. Don' t know what it is exactly. And yes, any blade over 4" is stretching it' s capabilities.

As far as diamond sleeves/ stones in general, they are a plus IME. It allows for quick removal/ reprofiling and for starting up very dull blades.

I recommend the Spyderco units over the Lansky clamp system.
Nakano is offline  
Old September 18, 1999, 07:43 AM   #5
Rich Lucibella
Staff
 
Join Date: October 6, 1998
Location: South Florida
Posts: 10,156
Nankano-
Plane Geometry:
Think of the blade fixed in the clamp as the base of a right triangle.
The height is a given, based on the clamp setup.
However, the length of the hypotenuse keeps changing as the the guiderod is pulled thru the stroke from one end of the stone to the other and one end of the blade to the other.

With constant base and height and changing hypotenuse something's gotta "give". That "something" is the included angle.

Aw, heck. Just trust me on this!
Rich
Rich Lucibella is offline  
Old September 22, 1999, 07:38 PM   #6
slabsides
Member In Memoriam
 
Join Date: May 27, 1999
Location: Maine
Posts: 614
Bethatasitmay, the one time I used a Lansky rig, borrowed, to fix the skewed-up edge of an original 9" Cold Steel Magnum Tanto, it did a good job...more uniform than my hands and eyes could have, so claims that it doesn't do the job on blades longer than 4" don't jibe with my experience. Are the diamond stones worth the money? Depends on whether you're edging 416 stainless or RC 61 tool steel. For some knives, it's super-superfluous. slabsides
__________
Afterthought: The tanto has a curved, 'draw-cut' blade. This might have made the difference.

------------------
An armed man is a citizen; an unarmed man is a subject; a disarmed man is a slave.


[This message has been edited by slabsides (edited September 22, 1999).]
slabsides is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06777 seconds with 7 queries