The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old September 5, 1999, 04:27 PM   #1
TMC
Member
 
Join Date: November 7, 1998
Posts: 92
Anybody have any good soft shooting 45LC handloads? My dad and I have been experimenting with 250 RNFP bullets and Bullseye 2400 and Unique Most of these shoot pretty sharp (read recoil). The 2400 is soft shooting but pretty erattic as far a velocities go (510 to 635 fps with the same charge size) guess thats what you get with slow magnum powder in a large case. I heard one guy talking about 150grain bullets Unique but 45 bullets that light are hard to find. Any sugestions?
TMC is offline  
Old September 5, 1999, 08:48 PM   #2
Long Path
Senior Member
 
Join Date: May 31, 1999
Location: N. Texas
Posts: 5,888
Try 6.0 g. of Unique with a 230gr LRN for about 700 fps. This is a real load, not some "poofter" load, but it's extremely comfortable. To give you an idea, we use 6.5g of Unique with a 230gr LRN for .45 acp, which has a much smaller case capacity, for duplicate factory ballistics (~840 fps).

It also has that lovely smoky look to it that is very appropriate to Cowboy shooting; there's something about Unique and lubed lead bullets that makes a pretty smoky combo.

Universal Clays, 231, and H110 also are okay. (U. Clays smokes less...)

[This message has been edited by Long Path (edited September 05, 1999).]
Long Path is offline  
Old September 5, 1999, 10:25 PM   #3
TMC
Member
 
Join Date: November 7, 1998
Posts: 92
Thanks I'll try it. How do you think it'll work with 250 grain bullets? I bought 2000 at the last gun show so I want to find some good combo.
TMC is offline  
Old September 9, 1999, 04:58 PM   #4
sjones
Senior Member
 
Join Date: May 15, 1999
Location: waxahachie,Texas
Posts: 337
Try 6.5 grains of unique and the 250 rnfp. I shoot those for plinking and target practice. That combination is very accurate in my black hawk and has no recoil at all.Any loading between 6 and 8 grains works real well.
sjones is offline  
Old September 9, 1999, 07:57 PM   #5
Bill Mitchell
Staff Alumnus
 
Join Date: October 15, 1998
Location: Roswell,GA
Posts: 433
Howdy TMC,

While there is no defined minimum required velocity,the preferred minimum is 650 fps. I shoot a 200 gr. RNFP bullet with 6.0 gr. of Titegroup. Titegroup is designed to be insensitive to position in the case,and thus is an ideal powder to use in large cases,as velocities are very consistent. I would hesitate to use a bullet lighter than 200 gr.,but I know some folks who use 185 gr. bullets. IMHO,anyone wanting to use a 150 gr.
bullet needs to be shooting .38's.

Bellicose Bill
Bill Mitchell is offline  
Old September 9, 1999, 11:33 PM   #6
TMC
Member
 
Join Date: November 7, 1998
Posts: 92
Thanks much all, we'll load some up the try'em!
TMC is offline  
Old September 12, 1999, 09:29 AM   #7
rw2astan
Junior Member
 
Join Date: September 2, 1999
Posts: 13
I was wondering if anyone has had any experience with W296 powder in reduced loads.
Winchester warns not to reduce there listed maximum loads as excessive pressures may develop. Is this true of ball powders in general? Does H110(suposedly the "same powder") have the same warning?
I load .44Mag. & .45 Colt with the 296 and want to reduce the listed loads somewhat, but the warning must be there for a reason. By the way, I'm using the Ruger Blackhawk .45 Colt with some strong hunting loads, that's why I use 296(lower pressures/higher velocities) at pressures I found listed at about 25,000 psi, very safe for the Ruger only & certainly not safe in the Colt Clones.
I'm using Unique & Universal for my cowboy loads but want somthing in between the cowboy & the max. for just some fun shooting.
2400 is not good for cowboy loads and I find that reducing this powder from its listed max leaves even more unburned powder behind.
Love the 240SWC & up to 300RNPP bullets in both calibers. Again my main concern is reducing the 296 loads.
Any input or discussion is greatly appriciated!
Thanx in advance.

P.S. Just thought I'd let you Know I'm on my way up to the farm to do some shooting with my Rossi 92 stainless steel .45 I picked up yesterday. Sure is a good looking gun, can't wait to shoot it.
rw2astan is offline  
Old September 13, 1999, 10:02 PM   #8
swifter...
Senior Member
 
Join Date: March 16, 1999
Location: So. CA Mountains
Posts: 540
rw2astan,
Don't reduce the 296 loads. Change propellants. 296 needs a certain pressure level to burn properly, and it will do weird things outside it.
A friend of mine found he had not only a lead SWC stuck in his barrel, he also had a bunch od (reduced) 296 packed against it.
OTOH, a pressure excursion is very likely, so he was lucky that he only had to figure out how to get the unburned powder and the stuck bullet out of the barrel. He might have been trying to get gun parts out of his face...


------------------
The Bill of Rights, and the Golden Rule are enough for civilized behavior. The rest is window dressing. Shoot carefully, swifter...

swifter... is offline  
Old September 18, 1999, 09:53 PM   #9
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 2,619
RW2ASTAN. Do not under any circumstances reduce your W-296 loads. On H-110, I believe Hodgden states not to reduce the load more than three percent. These guys are experts and the are not kidding. You could blow up your gun.
I normally do not give loads on the forum, but in your case I will break my rule.
In .44 Spl. cases, 240 gr. cast lead bullet with gas check, or plain base, 7.5 gr. Unique. Using .44 Magnum brass, 8.5 gr. Unique, same bullets.
In .45 LC, try 8.5 gr. Unique with a 250 gr. bullet. These are all good accurate loads that work in five .44's, and in four .45 LC's. Winchester large pistol primer in all load. Magnum primers are not necessary.

TMC. If you have read this far, try 7.0 gr. W-231 with a 230 gr. bullet in .45 LC. Accurate, and very pleasant to shoot.
Hope this helps out.
Paul B.
Paul B. is offline  
Old December 12, 2005, 06:44 PM   #10
joet47
Junior Member
 
Join Date: November 26, 2005
Location: Kentucky
Posts: 12
My experience with titegroup powder has been very good in the .45 colt. I use 6.3 grains of titegroup with the 200 gr RNFP bullet for decent velocity, good accuracy and low pressure.
joet47 is offline  
Old December 12, 2005, 08:48 PM   #11
Smokin_Gun
Senior Member
 
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
Good Load

I got a real good load, W-W cases W-W primers, 30gr of Goex FFFg, 255gr FP soft lead. Colt 3rd generation 1st Model Dragoon...
Target 25 yards.
__________________
"I Smoke Black Powder" "Favor an 1858 Remington"
SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A.
SASS# 19634, ...
Admin:http://blackpowdersmoke.com/oldcoots/index.php
Smokin_Gun is offline  
Old December 12, 2005, 09:59 PM   #12
MPP1423
Senior Member
 
Join Date: September 10, 2005
Location: GOODLETTSVILLE,TN
Posts: 298
I Use 7-7.5 Grn Of Hp38 By Hogdon With A 200 Rnfp And It Has Good Accuracy And Light Recoil.
MPP1423 is offline  
Old December 12, 2005, 10:06 PM   #13
Old Dragoon
Senior Member
 
Join Date: October 31, 2005
Location: The Republic of Californi
Posts: 581
This isn't 45LC, but.....

I am getting ready to handload the 44 Remington loading of the 44 Colt. This is a 248 Grn Outside lubed heeled bullet, 30 grns. BP in 44 Colt(Starline)Win. Large Pistol Primers..
This will be loaded also with 4.5 to 5 grns. Unique for a smokeless Cowboy load of 650 FPS.

I would load this with 38 Grn in a cut down rim 44 Mag case...but the darn things poke their little noses out the mouth of the chamber. (Kirst 44 Rem Konverter)

I can load 35 grn in a 44 Special case with the rim turned down and that will approximate the original 45 LC of 35 Grn. BP and a 250 Grn Bullet and these keep their noses just inside the chamber mouth. . I intend to persue this loading.

All of the gear for the original 44 Rem loading of the 44 colt(for 1875 Remington or Remington conversion...And the Kirst 44 Remington Konverrter(crimper die, Sizer Lubricator dieand the bullets) are available at Old West Moulds,1175 17 1/4 Rd. Fruita, CO 81521.
Old Dragoon is offline  
Old December 13, 2005, 12:54 AM   #14
MPP1423
Senior Member
 
Join Date: September 10, 2005
Location: GOODLETTSVILLE,TN
Posts: 298
Dragoon,
Since You Brought It Up,i'd Like To Say Again That Your Conversion Is Just Awesome!!!!! It Looks 100 Yrs Old And I Wish I Had The Know How To Make Mine Look As Well As Yours But I Doubt It!! I Will Have One Of The Frist Coverter Though In .45 But I Want To Shoot .45 Scholfield In Mine.i Have Never Fired This Round But I Think Thats My Choice.what Do You Think About This Round Dragoon?
MPP1423 is offline  
Old December 13, 2005, 01:30 AM   #15
Old Dragoon
Senior Member
 
Join Date: October 31, 2005
Location: The Republic of Californi
Posts: 581
The 45 schofield is a shorter case than 45LC, one reason that the 45 Schofield was not used by the Army very long. You could not interchange the rounds. The 45 Schofields were on the loosing end of that deal. The Colts and Remingtons could use the 45 Schofield and the 45LC, but not the other way around. Fell from favor very quickly. That is the extent of my knowledge of the 45 Schofield.

Either will round work in the 45LC Kirst Konverter.

Perhaps Mec Or Smokin Gun can supply more info. My preference of the two would be 45 LC since you can buy that load in Cowboy FPS (less then 1000FPS) but if you're going to reload then it doesn't make any difference except the number of grns you can cram into the case(BP that is).

I just found a 44 S&W spl. case, turned down the rim and can load 35 Grn.3FG BP with the 248 Grn Old West 44 Rem bullet. and it, for sure, just clears the chamber mouth. This load approximates the original 45 LC, but in 44 Rem.
Old Dragoon is offline  
Old December 13, 2005, 08:06 AM   #16
MPP1423
Senior Member
 
Join Date: September 10, 2005
Location: GOODLETTSVILLE,TN
Posts: 298
Thanks Dragoon!i Did Plan On Reloading Them Cause I Already Reload The 45 Colt.i Just Thought I'd Try Something Different For A Change.i Would Most Likely Reload With The 777.i Load My 45 Colt's W/25-30 Grs Of 777 And A 200 Gr Rnfp Bullet .i Also Take Up The Space With Wads.this Load Shoots Great.
MPP1423 is offline  
Old December 13, 2005, 11:22 AM   #17
Musketeer
Senior Member
 
Join Date: September 12, 2005
Posts: 3,732
I use 6.3 gr of Unique, CCI 300 LP Primers and a 250 gr RNFP for 45 Colt loads in my Uberti Cattleman (SAA clone). I have had good accuracy with it and it has been consistent. Alliant Powder lists the load as 6.0 - 7.5 max (I believe, confirm it on their website) for the 250gr 45 Colt. I settled on 6.3 as I am using a LeePro 1000 and the powder disc is a little limited in fine tuning. Using the .76 size disc gives me 6.3 grains. The next size, .82, is right up around the max. That beats up a SAA clone a little too much for my comfort.

One word of advice, WATCH FOR DOUBLE CHARGES. That is a big case you are loading and the smokeless powders are much more efficient. If you double charge you may not overflow the case, so you really need to keep both eyes on the job.
Musketeer is offline  
Old December 14, 2005, 02:42 AM   #18
Smokin_Gun
Senior Member
 
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
Old Dragoon, the Kirsts will take Schofield .44's the old version R&D drop-ins will not unless modified to accept the Schofield rim, but it has been done. I believe I was told the New R&D drop-in 6 shot will accept the Schofield. The new ones have a nurled ring around the cylinder. my Dragoon is the old style and is smooth and has the slots where you can see if there is a case in a chamber or not. I perfer the .45LC as I can load it any way I want. The Schofield has a limited max and that's one reason the Military rejected them...the other reason was that Colt beat them to it.
Do you use healed or hollow base bullets in the .44-40? I'm sure you do, but more wondering where you get them or the mold from, just curious.
__________________
"I Smoke Black Powder" "Favor an 1858 Remington"
SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A.
SASS# 19634, ...
Admin:http://blackpowdersmoke.com/oldcoots/index.php
Smokin_Gun is offline  
Old December 14, 2005, 09:17 AM   #19
Old Dragoon
Senior Member
 
Join Date: October 31, 2005
Location: The Republic of Californi
Posts: 581
SG,
Nope they are .451 Dia Drive band, X ,429 dia heel X .248 grn. heeled bullets with crimp groove and 3 driving bands, two lube grooves RFN.



44 Colt Bear Creek, .451 ball/44 Rem Mag case, 44 Rem./Colt

They are the 44 Rem/Colt 30 Grn.s BP This is the authentic load for original Remington and Colt Conversions discontinued in 1895. Old West re-introduced thois load for new Rem. conversions. I see no reason,that they would not work in new colt conversions as well..,except that no one makes a 44 Colt conversion Cylinder for the large colts. The new 44 Colt open tops take a .439 (the bear Creek shown) as they are not the original open top/conversion .451 groove cal.
Old Dragoon is offline  
Old December 14, 2005, 09:28 AM   #20
Smokin_Gun
Senior Member
 
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
I can't remember if you mentioned what barrel you have for your Rem. Is it a
.429" type .44 barrel or do you use the standard barrel that came with it .452 x .440?
__________________
"I Smoke Black Powder" "Favor an 1858 Remington"
SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A.
SASS# 19634, ...
Admin:http://blackpowdersmoke.com/oldcoots/index.php
Smokin_Gun is offline  
Old December 14, 2005, 09:35 AM   #21
Old Dragoon
Senior Member
 
Join Date: October 31, 2005
Location: The Republic of Californi
Posts: 581
It's the bbl that came with the gun flat off the net. I'm not about to change bbls...yet. I slugged the bbl and it is closer to .451. X .439 Nom BP cylinder chambers shave just a bit off .451 balls.
Old Dragoon is offline  
Old December 14, 2005, 09:43 AM   #22
Smokin_Gun
Senior Member
 
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
I'm cornfusin myself here. Bare with me please? Is it a .44 special conversion you have? I wa sthinkin it was .44-40, you know the bottle necks. I should a known better...they offer .44spl/.44 russian correct? The pics helped my mind get straight.
__________________
"I Smoke Black Powder" "Favor an 1858 Remington"
SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A.
SASS# 19634, ...
Admin:http://blackpowdersmoke.com/oldcoots/index.php
Smokin_Gun is offline  
Old December 14, 2005, 09:52 AM   #23
Old Dragoon
Senior Member
 
Join Date: October 31, 2005
Location: The Republic of Californi
Posts: 581
I think they do, but mine is marked 44 colt (on the box) Konversion (called 44 Rem in Kirst Litature. You load the original 44 Rem bullet to shoot in the '58 from Uberti and Pietta.
Nope not 44-40.
The 44 colt bullet from Bearcreek almost falls thru the bbl with minor, if any land marks, but for some reason they did shoot pretty well. at 15 yds. must have expanded just enough. anyway i have abour 450 of those loaded up and I either shoot them up or pull them and save the BP and cases and can the bullets. They are for the 1872 new Open tops. I owned one but could not keep it tight and sold it to a guy that said he'd work with the looseness....I wouldn't.
Old Dragoon is offline  
Old December 14, 2005, 10:01 AM   #24
Smokin_Gun
Senior Member
 
Join Date: December 4, 2005
Location: Mojave Desert, CA
Posts: 1,195
Is it the Drop -in cyl. from Kirst like this one, 6 shot .44Rem 248gr heeled bullets? http://www.riverjunction.com/kirst/konverterdropin.html

I really like the 6 shot idea, that's why I didn't get Kirst in .45LC only 5 shot. I'd rather have 6 shots R&D and it be the Civil War style Drop in.
__________________
"I Smoke Black Powder" "Favor an 1858 Remington"
SGT. Smokin' Gun, Mosby's Rangers 43rd Virginia Cavalry C.S.A.
SASS# 19634, ...
Admin:http://blackpowdersmoke.com/oldcoots/index.php
Smokin_Gun is offline  
Old December 14, 2005, 10:02 AM   #25
Old Dragoon
Senior Member
 
Join Date: October 31, 2005
Location: The Republic of Californi
Posts: 581
That's the one!
Old Dragoon is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:34 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.10988 seconds with 7 queries