The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 15, 2005, 11:19 PM   #1
WisconsinDave
Member
 
Join Date: February 5, 2005
Location: Southern Wisconsin
Posts: 32
Lee shellholders in an RCBS press ?????

I need a question answered before I place a order for some reloading equipment that I need. Instead of buying shellholders for my RCBS press one at a time, I have been thinking about buying the 11 pc set that Lee offers. I just want to make sure that the Lee shellholders will fit in my RCBS press with no problems ? The catalogs say that they will fit in "MOST" presses. I use a Lee Auto-Prime tool and plan on ordering the 11 pc set of shell holders for it at the same time.

Thanks for the help

Dave....in Wisconsin
WisconsinDave is offline  
Old May 15, 2005, 11:42 PM   #2
farmall
Senior Member
 
Join Date: December 7, 2004
Location: Beatrice Nebraska
Posts: 609
Dave, I dont use RCBS press myself, but guys at work do with Lee shellholders. They dont report any problems. I use them myself in Pacific, Herters, (with adapter to replace screw in shellholders) and Lyman without problems. Hope this helps. Andy
farmall is offline  
Old May 16, 2005, 12:11 AM   #3
xXStarScreamXx
Senior Member
 
Join Date: February 11, 2005
Location: Nor*Cal 707
Posts: 353
I use an RCBS Press and lee shellholders. Works perfectly
__________________
I still don't see why cannibalism is a crime.
xXStarScreamXx is offline  
Old May 16, 2005, 12:19 AM   #4
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,336
Make sure you get the press shellholders and not the ones for the Auto Prime.

I've used Lee shell holders in my RCBS and my Lyman T-Mag presses without any problems at all.
Mike Irwin is offline  
Old May 16, 2005, 05:50 AM   #5
Tim R
Senior Member
 
Join Date: November 30, 2004
Location: God's side of Washington State
Posts: 1,601
As stated make sure the shell holders you buy are not for the Auto Prime, although that would give you a good reason to buy the Auto Prime 2. (Only thing made by Lee I use)

I have used Lee shell holders on my RCBS press without problem. IMHO, however, the shell holders made by others seem to work better and/or held to different tolerances than the Lee's. I now use only those shell holders made by RCBS.
__________________
God Bless our Troops especially our Snipers.
Tim R is offline  
Old May 16, 2005, 08:23 PM   #6
Leftoverdj
Senior Member
 
Join Date: October 15, 2004
Posts: 934
Given the enormous price difference, a set of the Lee shellholders is well worth having on the bench. I did run into one holder that was too large to snap into my RCBS ram. Could have sent it back to Lee had I really wanted to bother.
Leftoverdj is offline  
Old May 18, 2005, 07:47 AM   #7
MADISON
Senior Member
 
Join Date: January 1, 2000
Location: Roanoke, Virginia
Posts: 2,678
Lee shellholders in an RCBS press

YES they will work.
What irritates me is the "flat spot", on the LEE, you encounter as you slide the case into the shell holder.
You can use Lee, RCBS, Lyman and Hornady interchangablely. I do.
MADISON is offline  
Old May 18, 2005, 09:15 AM   #8
tcov
Member
 
Join Date: June 17, 2004
Location: OLYMPIC PENINSULA WA
Posts: 51
Lee shellholders work fine in the RCBS presses. I have had problems with them in the RCBS hand priming tool. The inside taper is different than RCBS holders causing them to fit too tight over the plastic feed tube. I don't know if they are all that way or just the ones I've tried.
tcov is offline  
Old May 18, 2005, 03:00 PM   #9
caz223
Senior Member
 
Join Date: May 15, 2002
Location: Michigan
Posts: 1,383
I have 2 lee shell holders.
The 10/.40 works perfectly in both RCBS presses I used it with.
The .45 colt shell holder worked poorly, and as I got a progressive shortly after, I don't know if genuine RCBS shell holders would work any better (Small rim).
__________________
I'm not just a gun.
I'm YOUR gun.
(Hold me.)
caz223 is offline  
Old May 21, 2005, 04:08 PM   #10
Kamicosmos
Senior Member
 
Join Date: January 31, 2002
Location: Kansas City, Missouri
Posts: 193
Quote:
I have had problems with them in the RCBS hand priming tool. The inside taper is different than RCBS holders causing them to fit too tight over the plastic feed tube.
I notice the same thing with my Lee shellholders and my RCBS hand primer.
My Lee shellholders work just fine in my RCBS press though.
__________________
"Dreams only have meaning because we struggle in the waking world."

-- Major Motoko Kusanagi GitS:SAC

Member of NRA and Western Missouri Shooters Alliance
Kamicosmos is offline  
Old May 23, 2005, 03:55 PM   #11
Popeye4
Junior Member
 
Join Date: May 23, 2005
Posts: 2
Dave,

The Lee shellholders will probably fit in your RCBS press (I haven't tried Lee, but Redding works in my RCBS press). The caveat is that I believe the shellholders are matched to the dies and you should use like shellholders to dies (i.e., Redding dies and Redding shellholder) if you want to ensure that case headspace is set back per die design (if you're full length resizing).

As an example, Redding makes a competition shellholder set that changes the headspace setting by 0.002" increments by making each shellholder slightly thicker from the case bottom to the top of the shellholder (where the die abuts). I don't know if all the die makers use the same dimensions on shellholders, but if actual results aren't verified I can see the potential for a problem.

Of course, I just ran a couple of .308 Win cases into a Redding resize die with an appropriate RCBS shellholder and their headspace matched the cases run through with the Redding standard shellholder, so I can say that Redding and RCBS .308 Win shellholders appear to be interchangeable.

This may not be that big of a deal if you're neck sizing for a bolt gun, but could be more of an issue in a minimum chambered gas gun. I'd want to be sure before something made a bigger "bang" than expected......

Doug
Popeye4 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08183 seconds with 7 queries