The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 6, 2005, 09:43 PM   #1
.30-06 Springfield
Junior Member
 
Join Date: May 6, 2005
Posts: 2
30-06 Primers

Hey,
I'm new to reloading and I was wondering what primers to use?
I read where it says 30-06 needs medium burning powder to be most efficent.
So I think regular rifle primers but at the local gun store they told me to use magmun primers and I would get a better load.
So which one is better regular or magnum?
I use IMR4350 powder.
.30-06 Springfield is offline  
Old May 6, 2005, 09:49 PM   #2
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,504
First of all, welcome to TFL!

Two pieces of advice are in order: 1) you'll often find that folks at gun shops don't always know what they are talking about. A blanket statement like that is irresponsible.
2) if you don't have one or two reloading manuals, you need to get them before you can think about any serious reloading.

IMR4350 doesn't require a magnum primer so a standard one is what you need. It isn't a question of which primer type is better, they are designed to ignite different types of powders. Think of it as similar to octane in gasoline. Some engines require a higher octane (higher compression needs a slower burning gasoline) and some require a lower octane. Neither type of modern gas is "better" than the other. (No discussions of additives is necessary - it's an analogy. )
Mal H is offline  
Old May 6, 2005, 10:09 PM   #3
armedandsafe
Senior Member
 
Join Date: January 9, 2005
Location: Moses Lake WA
Posts: 1,001
I've been loading 30-06 with IMR 4350 and standard primers for over 50 years, without ever feeling I needed magnum primers. Stick with the standards.

Get your manuals and read them. Also, get the Lyman Reloading Handbook and read it.

Be warned, though, reloading is ADDICTIVE!

Pops
__________________
Armed and Safe: Not just a theory

If it time to bury them, it is time to dig them up.
Remember, "Behind every blade of grass."
armedandsafe is offline  
Old May 7, 2005, 06:04 PM   #4
Tim R
Senior Member
 
Join Date: November 30, 2004
Location: God's side of Washington State
Posts: 1,601
Primers can make a difference on group size. I use IMR 4350 for my '06 hunting loads and use a std. CCI primer.
__________________
God Bless our Troops especially our Snipers.
Tim R is offline  
Old May 7, 2005, 06:46 PM   #5
DanV1317
Senior Member
 
Join Date: August 27, 2004
Posts: 330
i've been loading imr 4350 and 4064 for my 8mmm mauser with cci large rifle primers. no problems so far. Was shooting about 6 inches with factory ammo, got the group down to 3 (iron sights). probably could get closer, but i have been in a slump for the past 20 years with my aim (i'm 20 years old).
DanV1317 is offline  
Old May 7, 2005, 07:33 PM   #6
cracked butt
Senior Member
 
Join Date: December 22, 2001
Location: southeastern wisconsin
Posts: 537
I wouldn't bother with a magnum primer in a 30-06 unless you are using a ball powder. With IMR powders, use a standard primer.
cracked butt is offline  
Old May 7, 2005, 09:45 PM   #7
Ruger4570
Senior Member
 
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
There is absolutly no need for a magnum primer with the powder you are using in a 30-06. If you go to the ball powders, it might be helpful. Best bet is to follow the "recipe" in a loading manual. These loads have been tested and proven safe.
I also totally agree with MalH: just because some guy works in a gun shop doesn't make him an expert and I would never try a load recommended by anyone from any source without at least seeing how it stacks up against what my reloading manuals say. A safe ?? hot load in his gun could be a bomb in yours. Welcome and Good Luck
Ruger4570 is offline  
Old May 7, 2005, 10:43 PM   #8
.30-06 Springfield
Junior Member
 
Join Date: May 6, 2005
Posts: 2
I have a nosler reloading manual
I use 168 Ballistic slivertips
57 grains of imr 4350
But thanks for all the replys
.30-06 Springfield is offline  
Old May 9, 2005, 02:41 PM   #9
cheygriz
Senior Member
 
Join Date: May 11, 2002
Location: high up in the rockies
Posts: 2,232
I don't use magnum primers except in .300 WinMag and .375 H&H.

I've been using Remington 9 1/2 standard large rifle primers in my .30-06 and .308 loads for over 25 years. And I use **BALL powder* exclusively in both calibres. In my target guns, I have loads that shoot 1/2 nch groups in both calibres.
__________________
If you think a mighty military force is expensive, wait 'til you see what a weak one costs.
cheygriz is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:24 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07294 seconds with 7 queries