The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 4, 2005, 12:57 PM   #1
cobra81
Senior Member
 
Join Date: February 18, 2005
Location: Land of Lincoln
Posts: 301
30/06 Primers Backing Out

I shot approx 20 rounds in my Savage 30/06 the other night, and when I got home and examined my brass prior to reloading, I noticed that several of them wouldn't stand up on end; the primers were substantially backed out of the primer pocket. All the rounds were loaded with the same charge, which was not by any means close to the maximum charge for the 110 grain Hornady V-Max bullets I was using. I was just wondering what could be the possible culprit.....no case splitting or cracks were observed, and the brass was Winchester that I've reloaded 3 or four times. Thanks for any ideas.
cobra81 is offline  
Old May 4, 2005, 01:22 PM   #2
brickeyee
Senior Member
 
Join Date: December 29, 2004
Posts: 3,342
You may have to low a pressure. On firing the cartrdge is driven forward to the shoulder of the chamber, then the pressure forces the primer back slightly against the bolt, followed by the head of the cartridge being pushed back and stretching the case slightly. Lower pressure loads may not have enough pressure to stretch the case so the process stops after the primer is pushed back.
In many cases there will also be some blackening of the otside of the case neck from not sealing quickly and tightly enough to prevent some leakage.
If the loads are below the max try moving up a lttle bit.
brickeyee is offline  
Old May 4, 2005, 03:18 PM   #3
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,393
You may be setting the case shoulders back in resizing.
A Wilson case gauge is not expensive and is a big help in setting dies for normal cartridge headspace.
Jim Watson is offline  
Old May 4, 2005, 04:51 PM   #4
Dave R
Senior Member
 
Join Date: January 7, 2000
Location: Idaho
Posts: 6,073
FWIW, I see primer setback when I'm using plastic training bullets in my 9mm, using primer only for power. IOW, I agree the primer setback my be from the light load you are using.
__________________
I am Pro-Rights (on gun issues).
Dave R is offline  
Old May 4, 2005, 08:36 PM   #5
Rodger Peterson
Member
 
Join Date: December 18, 2004
Location: Nevada
Posts: 93
I believe Jim Watson is correct. I have personally been through this myself.
Before you crank up the charge, try it again without pushing the shoulder back so far. Case Guage is the answer, but if you don't have one, back the sizing die out and try to chamber. If it doens't chamber, continue to push shoulder back till it does. Try it again, bet you will find the solution.
Rodger Peterson is offline  
Old May 4, 2005, 09:40 PM   #6
cobra81
Senior Member
 
Join Date: February 18, 2005
Location: Land of Lincoln
Posts: 301
Thanks guys for the excellent suggestions. I definitely should have a headspace gauge on my bench, and I will try to get one soon. As soon as you mentioned black fouling on the neck of the case, I thought "Yep, that's one other thing I observed but forgot to include in my original post." I aim to check the headspace, and then review the load for possible upward adjustment. I have chrono'd several of these rounds and it seems to be in the neighborhood of what Lyman's says.
cobra81 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:26 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06991 seconds with 7 queries