The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 20, 2005, 04:12 PM   #1
Kayser
Senior Member
 
Join Date: May 29, 2002
Location: Illinois :(
Posts: 550
Strategy for catching brass at indoor range?

I finally fired off my first reloaded rounds today. Whee! 5.4 gr of unique behind a 230 gr bullet was considerably more mild than your average WWB load.

Anyways, I was having a heckuva time finding my brass. I think my recycling rate was probably only 75% or so. The others disappeared into the void like socks in a dryer.

So - what kind of strategies do you guys use to make your brass more findable? I found that standing a bit further back in the lane caused more rounds to bounce into my lane, and I made sure to sweep the place clean so that it was easy to identify my own rounds. It also occurred to me that I could mark my brass with a marker or something. 1 stripe for factory new loads. 1 additional stripe for every time a round has been reloaded.

But even still - it sucks to lose that much brass. Any suggestions?
Kayser is offline  
Old March 20, 2005, 04:17 PM   #2
novus collectus
Junior member
 
Join Date: March 15, 2005
Location: Maryland
Posts: 940
Been wondering the same thing. If you use one of those attachable brass catchers then will it affet the function or aim of the gun?
novus collectus is offline  
Old March 20, 2005, 08:43 PM   #3
Guy B. Meredith
Senior Member
 
Join Date: August 29, 1999
Location: Salem, Oregon
Posts: 1,578
Shoot revolvers
Guy B. Meredith is offline  
Old March 21, 2005, 10:21 AM   #4
Colduglandon
Senior Member
 
Join Date: March 5, 1999
Location: Mass
Posts: 480
I use the firing position on the far right so I don't have so far to chase the casings. Or like Guy said I bring my revolver.
__________________
From the People's Republic of Massachusetts
Colduglandon is offline  
Old March 21, 2005, 02:10 PM   #5
tjhands
Senior Member
 
Join Date: January 20, 2005
Posts: 1,708
Yeah, it's like an Easter egg hunt every time I shoot. I painted the brass in pastel colors to make it more fun....ahem, just kidding.

On one hand, I like shooting outdoors more than indoors, but my brass recovery rate is only around 75% outside. Lots of grass and dirt end up in the tumbler as well. Oh well, it's a trade-off.
tjhands is offline  
Old March 21, 2005, 04:37 PM   #6
Russ5924
Senior Member
 
Join Date: February 18, 2005
Posts: 1,874
I like you kind of guys after you leave I PICK IT UP
__________________
Russ5924
Russ5924 is offline  
Old March 21, 2005, 05:32 PM   #7
Guy B. Meredith
Senior Member
 
Join Date: August 29, 1999
Location: Salem, Oregon
Posts: 1,578
One of the things I REALLY don't like about shooting in competition with auto shooters is that all competitors are required to go around scrounging for the last shooter's brass--my back and knees are good, but I don't like to tempt fate. So much better shooting all-revolver ICORE. Just look for the little piles or moonclips.
__________________
Smart Gun + 1 Battery + 3 Wires = Dumb Gun

PC = Agenda driven groupthink filter on reality.

Apostrophes denote ownership or missing letters NOT plurals!
Guy B. Meredith is offline  
Old March 23, 2005, 09:19 PM   #8
AustinMike
Senior Member
 
Join Date: October 25, 2004
Location: Austin, TX
Posts: 171
The outdoor range I go to has a nice setup. Each stand has some netting on the right side that attaches to a feed ramp that goes to a bucket. Works great for most guns. It's great for my Desert Eagle and that expensive .44 brass! My Taurus PT145 flings the brass high and out of the stand though.
AustinMike is offline  
Old March 24, 2005, 09:14 AM   #9
Master Blaster
Senior Member
 
Join Date: October 11, 1999
Location: One of the original 13 Colonies
Posts: 2,027
brasscatcher

it will take you to the disclaimer page click I agree and you will see the brass catcher.

You can make one with a welding torch and some netting also, or I have seen them made from PVC with PCc glue and mosquito netting
__________________
The difference between Democrats and Republicans is like the difference between a poop sandwich, and a poop Sandwich with mustard.
Master Blaster is offline  
Old March 26, 2005, 01:01 AM   #10
Blue Heeler
Junior member
 
Join Date: October 4, 1999
Location: Queensland
Posts: 1,043
At my range there are portable screens about 3ft x 6ft made from a light wooden frame covered with plastic shadecloth - these stop the brass from flying everywhere and going down the neck of the guy at the next station.
Blue Heeler is offline  
Old March 26, 2005, 09:31 AM   #11
MADISON
Senior Member
 
Join Date: January 1, 2000
Location: Roanoke, Virginia
Posts: 2,678
Catching brass on indoor range.

Hang an old shirt, on a coat hanger, on the right side of your lane. A few shots will tell you the correct angel.
The brass will hit the shirt and drop straight down.
MADISON is offline  
Old March 26, 2005, 01:23 PM   #12
hawk
Member
 
Join Date: May 16, 1999
Location: Fremont, NE
Posts: 22
Shoot really light loads so they don't cycle the slide. (just kidding)
hawk is offline  
Old April 30, 2005, 01:36 AM   #13
OfcrBill
Member
 
Join Date: November 12, 2004
Location: New Mexico
Posts: 62
The brass hunt

At the indoor range, I usually go during lunchtime when few people are present. I have a buddy distract the range staff with silly antics. I then move in, I grab the large broom and start pushin' all the brass towards my lane and scoop 'em into my range bag. It's quite comical and I'm expecting to get banned soon. Seriously, I just ask the staff If I can snagg some brass from their brass bins. Bill
__________________
A Proud Veteran, USN
USS Whipple FF 1062
USS Dixon AS 37
USS Jason AR 8
USS Kitty Hawk CV 63
OfcrBill is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:38 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08808 seconds with 9 queries