The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 16, 2005, 06:19 PM   #1
AdamHnetka
Junior Member
 
Join Date: March 15, 2005
Posts: 3
43 Mauser

Does anyone know if brass and cast lead bullets can be purchased for the 43 mauser? I have a 1887 model in good condition, and I would like to load for it. Also, I live in Canada, has anyone bought reloading components over the internet and had them shipped to Canada? If anyone has any info, I would appreciate it. Thanks.
AdamHnetka is offline  
Old April 16, 2005, 07:14 PM   #2
Leftoverdj
Senior Member
 
Join Date: October 15, 2004
Posts: 934
I knew a fellow who was shooting an 1871 Mauser for the same cartridge, so it can be done. I strongly suspect that your best route for bullets is a custom mould. You're going to need to slug that bore and order your mould .002 over. Huntington's is the first place I would check for brass and dies. That's very odd brass, but the last I heard basic cases were available to be trimmed and reformed.

What I hear from our Canadian friends is that fees and duties will eat you up, but it can be done if you must. Best to get everything in one package to hold down on those costs.
Leftoverdj is offline  
Old April 17, 2005, 03:51 PM   #3
EchoFiveMike
Senior Member
 
Join Date: February 12, 2000
Posts: 416
RCBS makes a mold that normally drops them about 375gns and .448 diameter when cast from 20:1 alloy. Bertram and BELL both make cases, but the Bertram tends to be cheaper and quality is fine. As far as not casting yourself, here's a place that does loaded ammo, but I have not used any yet.

Aardvark Labs LLC
Glenn Anderson pres
PO Box 3180, Glen Ellyn IL 60137
#630-620-5244

They have a 43 Mauser load with a 346gn lead bullet. I have not checked it, but it ATB a binary tin:lead alloy, which is what you want for the older rifles. S/F...Ken M
EchoFiveMike is offline  
Old April 17, 2005, 08:13 PM   #4
drinks
Senior Member
 
Join Date: November 6, 2004
Posts: 405
.43 mauser

Midwayusa has the Bertram brass, about $35 per 20.
No one seems to sell bullets in .446, but a number of cast bullets in .451-452 are available and could be sized down .
The first thing to do is slug the barrel and see what size you really need.
Cast bullets usually shoot better if they are .001-.003" oversize.
A listed load for the .43 mauser is 30-33gr IMR 4198, of course ,start out on the low side. Since it is very similar to the .45-70, likely most .45-70 trapdoor loads would be fine.
Mountain molds is supposed to make custom molds for about $50 and up.
You might explore their web site.
The original bullet weight was about 375gr.
Lee makes custom sizer dies for $25 , just use them in your regular press.
Don
drinks is offline  
Old April 22, 2005, 12:42 PM   #5
Leftoverdj
Senior Member
 
Join Date: October 15, 2004
Posts: 934
Lee #2 has data using 4198. Looks suspiciously like .45-70 data to me.
Leftoverdj is offline  
Old April 22, 2005, 12:58 PM   #6
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 10,898
Buffalo Arms has most of what you need for any BPCR. I don't know if they export, though. Call them up.
www.buffaloarms.com
Jim Watson is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06777 seconds with 9 queries