2 3/4" shotshell in a 3" Mod?

Clone · April 6, 2005, 03:04 PM

Im a bit new to shotguning and have a rossi 12GA break down single shot. I was wondering if its ok to use 2 3/4" shotshells in a 3" modified choke gun.

mete · April 6, 2005, 03:21 PM

No problem.

Dave McC · April 6, 2005, 04:56 PM

Shorter shells will work. On any barrel, the chamber length should be marked. If it says for 2 3/4" only, no 3" or 3.5". If it says 3", 2 3/4" shells will work also.

The big 3.5", same same.

In your Rossi, I vehemently recommend 2 3/4" LIGHT loads. The little singles like yours are very light, and mag loads will tear you a new one if your fit and form aren't up to par.

HTH....

Clone · April 7, 2005, 01:06 AM

thanks for the info. what kinda recoil can i expect from 3' #4 or #6 shotshell im not into slugs or 000,00,0 shot. im 6"2' 250lbs.

Jelly · April 7, 2005, 02:35 AM

http://www.chuckhawks.com/shotgun_recoil_table.htm

I'm much smaller than you and fired half a box of Remington High-Velocity Magnum Turkey Loads from a 6-7lb. single-shot New England Pardner (with Pachmayr slip-on recoil pad) that had an estimated recoil energy of around 55 ft. lbs.

Certainly noticeable, but nothing too brutal.

Dave McC · April 7, 2005, 07:26 AM

Clone, enough. With good form and fit, no pain.

Clone · April 7, 2005, 01:53 PM

thx again for the info. i think ill get a http://www.rossiusa.com/products/RecoilPadDetail.cfm for the rossi. better to spend $10 on a recoil pad and enjoy the shooting than have a bruised shoulder.

April 6, 2005, 03:04 PM	#1
Clone Senior Member Join Date: March 16, 2005 Posts: 227	2 3/4" shotshell in a 3" Mod? Im a bit new to shotguning and have a rossi 12GA break down single shot. I was wondering if its ok to use 2 3/4" shotshells in a 3" modified choke gun.

April 6, 2005, 03:21 PM	#2
mete Senior Member Join Date: June 14, 2004 Location: NY State Posts: 4,937	No problem.

April 6, 2005, 04:56 PM	#3
Dave McC Staff In Memoriam Join Date: October 14, 1999 Location: Columbia, Md, USA Posts: 8,831	Shorter shells will work. On any barrel, the chamber length should be marked. If it says for 2 3/4" only, no 3" or 3.5". If it says 3", 2 3/4" shells will work also. The big 3.5", same same. In your Rossi, I vehemently recommend 2 3/4" LIGHT loads. The little singles like yours are very light, and mag loads will tear you a new one if your fit and form aren't up to par. HTH....

April 7, 2005, 01:06 AM	#4
Clone Senior Member Join Date: March 16, 2005 Posts: 227	thanks for the info. what kinda recoil can i expect from 3' #4 or #6 shotshell im not into slugs or 000,00,0 shot. im 6"2' 250lbs.

April 7, 2005, 02:35 AM	#5
Jelly Senior Member Join Date: November 22, 2004 Location: Kentucky Posts: 238	http://www.chuckhawks.com/shotgun_recoil_table.htm I'm much smaller than you and fired half a box of Remington High-Velocity Magnum Turkey Loads from a 6-7lb. single-shot New England Pardner (with Pachmayr slip-on recoil pad) that had an estimated recoil energy of around 55 ft. lbs. Certainly noticeable, but nothing too brutal.

April 7, 2005, 07:26 AM	#6
Dave McC Staff In Memoriam Join Date: October 14, 1999 Location: Columbia, Md, USA Posts: 8,831	Clone, enough. With good form and fit, no pain.

April 7, 2005, 01:53 PM	#7
Clone Senior Member Join Date: March 16, 2005 Posts: 227	thx again for the info. i think ill get a http://www.rossiusa.com/products/RecoilPadDetail.cfm for the rossi. better to spend $10 on a recoil pad and enjoy the shooting than have a bruised shoulder.