The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 26, 2005, 10:54 PM   #1
FP-74
Member
 
Join Date: November 10, 2004
Location: northeast
Posts: 21
Dirty first loads

Hello again! Fired my first 100 rounds of .38 spec. after test firing a few. And i noticed my m-60 S&W was pretty dirty! (especially around the cylinder) spent cases are also somewhat blackened. i used 4 grains of win231, remington primers, and a 158 gr. round nose lead bullet. is this normal? they all seemed to shoot ok. i've shot this gun a few times, but never this many rounds of my reloads. thanks in advance for your thoughts!
FP-74 is offline  
Old March 27, 2005, 07:28 AM   #2
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,204
clone?

I, too, shot some 38 Special 158g LRN / 4.0g W231 yesterday (ignited by Federal 200 SPM primers).

Smokey but accurate.


What happens is insufficient pressure to push the case walls fully against the chamber walls; you get sooted cases from the blow-back.

Notice I used SPM primers?
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old March 27, 2005, 09:24 AM   #3
Russ5924
Senior Member
 
Join Date: February 18, 2005
Posts: 1,874
W231 is like that I use 3.7 with that bullet but after 50 rounds have a Black thumb.But my cases don't seem to burn that bad.
__________________
Russ5924
Russ5924 is offline  
Old March 27, 2005, 10:05 AM   #4
smokin54
Senior Member
 
Join Date: January 7, 2005
Posts: 193
4 grains of 231 is a starting load in my lee manual , A little warmer load will raise the pressure and get more case exspansion and seal the chamber better , This should reduce the blackening . I did this for 45 colt .
As always refer to your loading manual before you change your load
smokin54 is offline  
Old March 28, 2005, 07:28 PM   #5
norielX
Senior Member
 
Join Date: January 10, 2001
Location: Texas
Posts: 164
Experienced the same with my starting load of AA#5

I loaded behind a 158 gr LSWC. I thought I was shooting black powder!
They were accurate, and out of my 4" 686, I felt like Jerry Miculek on the steel targets! Yeah, I ended up with a black cylinder, black left hand from the speed reloads, but a huge grin at the end of the day! If I had a M28, It'd probably feel like I was shooting a .22!
__________________
-- norielX
norielX is offline  
Old March 29, 2005, 10:00 PM   #6
FP-74
Member
 
Join Date: November 10, 2004
Location: northeast
Posts: 21
thanks

thank you very much for your response! i'll check load data and maybe heat it up a bit. thanks again!
FP-74 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06401 seconds with 7 queries