The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 14, 2005, 07:35 PM   #1
bill k
Senior Member
 
Join Date: December 9, 2004
Location: Dog Creek, CA
Posts: 457
reloading 44 special

I want to try reloading a few 44 special rounds to see how the recoil is compared to a 44 mag. I don't have any 44 special brass, can I just trim 44 mag brass down to the correct length?
__________________
Retired Air Force
8th TFW
The Wolfpack
bill k is offline  
Old March 14, 2005, 08:46 PM   #2
jem375
Senior Member
 
Join Date: May 31, 2002
Location: Minnesota
Posts: 390
just shoot 44 mags with a target load of 7.5-8 grs. of Unique with a 240-250 gr. bullet....same thing..
__________________
Life is too short to spend it with an ugly gun.....
NRA Life Member
jem375 is offline  
Old March 14, 2005, 09:55 PM   #3
Ruger # 1
Member
 
Join Date: December 6, 2004
Location: Ohio
Posts: 86
There is no need to trim your brass. 90% of the loads I use in my .44 Mag. are .44 Special loads. I just use 44 special data in Magnum brass. I usually use the max. Special load data for the Magnum brass because of the slightly larger case capacity of Magnum brass. In other words, I wouldn't use 44 Special starting loads in Magnum brass.

44 Special loads are plenty potent, and they're easier on you and your gun. I can shoot full house loads in my .44, but I definitely enjoy the lighter loads more. One of my favorites pushes a 180 gr. Hornady XTP at about 1100 fps.
Ruger # 1 is offline  
Old March 15, 2005, 06:34 AM   #4
zeke
Senior Member
 
Join Date: November 17, 1999
Location: NW Wi
Posts: 355
180 gn jhp's over 10.0 gns unique (44 mag brass, Fed 150 primer), get about 1150 fps from 4 in 44 mag, with excellent accuracy. Slighty Warmer than 44 special. Haven't tried Red Dot or 231 yet, but might get that accuracy at slower velocity.

Speer has reloading data for 44 mag and 200 gn GD on their website. Lighter charges of Red Dot and 231 gave excellent accuracy at about 1050 fps (again, 4 in barrel). Standard Speer Blaser 44 special 200 GD loads used to get about 900 fps from 4 in.
zeke is offline  
Old March 15, 2005, 01:39 PM   #5
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 2,598
The late Skeeter Skelton liked 7.5 gr. of Unique with a 240 gr. cast lead semiwadcutter in the .44 Spl. To get approximately the same results, try 8.5 gr. of Unique in the .44 magnum brass. Works for me.
Paul B.
__________________
COMPROMISE IS NOT AN OPTION!
Paul B. is offline  
Old March 15, 2005, 02:15 PM   #6
Edward429451
Junior member
 
Join Date: November 12, 2000
Location: Colorado Springs, Colorado
Posts: 9,494
Depending on how much 44 mag ammo you load, you might want to go ahead and use 44 special brass for the simple reason of easier identification of the loads later on. Especially if you leave the maggie loaded for awhile or leave ammo in speedloaders.

44 mag brass can be trimmed to 44 special length and on down to 44 russian length too. 0.97" for russian length. Sometimes I toy with the idea of trimming down somw mag brass just to mess with my friends to show off my '44 Mag' CA Bulldog... (bad idea, I know. I haven't done it)
Edward429451 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:38 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08382 seconds with 7 queries