UPDATE: 1919A4

The Rock · February 16, 2000, 10:12 PM

Your estwhile champion, The Rock, has found a source for kit, tripod and right hand side plate.
SARCO has kits for $335 and tripods for $385.

Socomm Mfg. has 80% rt. hand plates for $175. Contact bande@alltel.net or 803-442-9206
talk to Ernie or Todd. Hope to have more details on what exactly needs to be done to the plate. Ernie said that it "is a very easy machining step."

More tommorrow, I hope!

TR

fal308 · February 17, 2000, 10:57 AM

Good luck with your project. You are going to put up a photo of the finished project, I hope.

The Rock · February 17, 2000, 08:27 PM

Update:
I have ordered the kit from Sarco and well as the 2 manuals. They said that they are 3 weeks behind for shipping, so I figure I'll have it in a month.

The plate just needs to be decked, which according to Ernie, should be about $50 to have done at your local machine shop.

When I have it complete, look for a photo expose here or my website.

TR

Daren Thompson · February 17, 2000, 09:26 PM

Keep me posted !! If this works well for U I WILL be next!

Later
Daren

Outlaw1 · February 17, 2000, 09:36 PM

Good luck Rock! I just got through "refurbishing" a discount M-6 flash hider for my A4, and geeezz!! I had an easier time restoring my 440-6 'cuda! I think it musta' been stored on the Utah during the attack on Pearl Harbor.

It really wasn't THAT bad, the time and effort was worth it, and it really turned out nice.
I'm working on a gun related page on my website, and I'll post some pics there hopefully next week.

------------------
We ARE the Militia!

February 16, 2000, 10:12 PM	#1
The Rock Senior Member Join Date: September 14, 1999 Location: Occupied VA, CSA Posts: 351	Your estwhile champion, The Rock, has found a source for kit, tripod and right hand side plate. SARCO has kits for $335 and tripods for $385. Socomm Mfg. has 80% rt. hand plates for $175. Contact bande@alltel.net or 803-442-9206 talk to Ernie or Todd. Hope to have more details on what exactly needs to be done to the plate. Ernie said that it "is a very easy machining step." More tommorrow, I hope! TR

February 17, 2000, 10:57 AM	#2
fal308 Staff Alumnus Join Date: October 12, 1998 Location: Missouri Posts: 1,989	Good luck with your project. You are going to put up a photo of the finished project, I hope.

February 17, 2000, 08:27 PM	#3
The Rock Senior Member Join Date: September 14, 1999 Location: Occupied VA, CSA Posts: 351	Update: I have ordered the kit from Sarco and well as the 2 manuals. They said that they are 3 weeks behind for shipping, so I figure I'll have it in a month. The plate just needs to be decked, which according to Ernie, should be about $50 to have done at your local machine shop. When I have it complete, look for a photo expose here or my website. TR

February 17, 2000, 09:26 PM	#4
Daren Thompson Senior Member Join Date: December 6, 1998 Location: Elizabethtown,KY,USA Posts: 457	Keep me posted !! If this works well for U I WILL be next! Later Daren

February 17, 2000, 09:36 PM	#5
Outlaw1 Senior Member Join Date: September 1, 1999 Posts: 314	Good luck Rock! I just got through "refurbishing" a discount M-6 flash hider for my A4, and geeezz!! I had an easier time restoring my 440-6 'cuda! I think it musta' been stored on the Utah during the attack on Pearl Harbor. It really wasn't THAT bad, the time and effort was worth it, and it really turned out nice. I'm working on a gun related page on my website, and I'll post some pics there hopefully next week. ------------------ We ARE the Militia!