The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > NFA Guns and Gear

Reply
 
Thread Tools
Old January 12, 1999, 03:45 PM   #1
Rocco
Member
 
Join Date: December 3, 1998
Location: South of the border.
Posts: 31
Although I have plenty of references to how to disassemble a M1 Carbine, the same does not apply to the M2.

Inasmuch the former strips to a few major groups, will the latter do as much?

The additional parts seem to be [haphazardly] connected, i.e., assembled in such a manner that stripping them may prove to be a quite involved matter.

I'd appreciate any help!


------------------
Si vis Pacem, Para Bellum -- Audaces Fortuna iuvat



Rocco is offline  
Old January 12, 1999, 08:15 PM   #2
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,601
Not meaning to be a smartass [Well, smartass, yes; hostile no :-)], but remember the M2 is simple enough that two generations of GIs had no trouble with it...

Take the metal stuff out of the wooden thingie, and slowly cycle the operating rod, and cycle the selector back and forth a few times. It oughta all be pretty obvious, since it'll only go together one way...

You can find the GI Manual at a lot of gun shows, in Paladin Press catalogues, etc.

Regardless of the effectiveness of their ".32-20" style cartridge, they're fun little chatterguns to shoot. And the stock won't break if you have to butt-stroke somebody, not like some Mattel Models I've seen. :-)

Enjoy!
Art Eatman is online now  
Old January 13, 1999, 02:46 AM   #3
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 17,105
This information is provided for entertainment purposes only:

1) Separate the receiver/barrel group from the stock. Unseat the operating slide spring and guide from the operating slide and, leaving the operating slide in place, remove the slide spring & guide.
2) Rotate the selector switch to semiautomatic (rear setting). Now, use the operating slide spring guide to dismount the selector switch spring.
3) Rotate the selector switch forward and afterwards, slide it to the rear to disengage it for removal.
4) Push the trigger housing/selector pin to unseat the disconnector lever and once you've done that, you may remove the disconnector lever.
5) Remove the trigger housing. Be careful as you don't want the disconnector plunger and spring to pop out.
6) Proceed as you would with an M1 Carbine.

Art is right, buy a manual. It's easier when you've got one of those and they're less than $10.
4V50 Gary is online now  
Old January 13, 1999, 07:47 AM   #4
Rocco
Member
 
Join Date: December 3, 1998
Location: South of the border.
Posts: 31
Art,

Smartass or no, you do have the benefits of familiarity and 'full supply'...

Things that I do not have! ;D

Residing - as I do - outside the US *DOES* make some things a bit more hard to get, i.e., there are no gun shows around, for one thing...

Paladin Press is a feasible option, although one is subject to postal/customs busybodies...

Hmmm, besides, I'd say that, after reading Gary's reply, that the actual procedures are a bit more involved than your description, wouldn't you?

I agree that the M2s are fun and handy to have around! That's why I got myself one, BTW.

Now, if I could get those pesky 30-rnd mags to work, ho-hum, I'd be just fine! <VBG>

Thanks for the input!

Rocco
Rocco is offline  
Old January 13, 1999, 07:58 AM   #5
Rocco
Member
 
Join Date: December 3, 1998
Location: South of the border.
Posts: 31
Gary,

Thanks a lot for the instructions!

I'll try the drill later tonight!

Accept my congrats for a very nice job!

Rocco

Rocco is offline  
Old January 13, 1999, 05:53 PM   #6
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,601
Rocco: Duh! Didn't realize you were out of country. The old "assume" word as to availability of info...I'm also 1,400 miles from my other home where most of the toys are, including my carbine...

In any manual, there are only a few pages with truly important information. Is ordinary letter-mail of only a few pages subject to inspection? Easy enough to Xerox or clip stuff and send it to you...

The carbine, Garand, Mini-14 and Springfield Armory M1A1 all come apart so easily. You just sort of "monkey around", and the next thing you know, you have a bunch of parts! Of course, getting things all back together...
Art Eatman is online now  
Old January 14, 1999, 11:50 AM   #7
Rocco
Member
 
Join Date: December 3, 1998
Location: South of the border.
Posts: 31
Art,

Thanx a lot for your offer! I'll greedily take it, shame on me...

OTOH, postal ordinances are such that it's safer to have them checked. I'll do so and return to you in private to avoid bandwidth clutter.

Thanx again!

BTW, the very first time I dismantled my GM .45ACP, the recoil spring plug went ballistic and shattered my glasses! It goes without saying that if I wasn't a blind bat without 'em in the first place, I could have ended with one less eye.

Huh, howz that for the Clumsy Award?

Regards,

Rocco
Rocco is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06480 seconds with 7 queries