The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 23, 2005, 02:40 PM   #1
Boudin
Junior Member
 
Join Date: December 14, 2004
Posts: 5
Marking brass lots

What's the best way to mark different lots of brass with the same headstamp so that they can be kept apart? Thanks, GasMan.
Boudin is offline  
Old January 23, 2005, 05:08 PM   #2
steveno
Senior Member
 
Join Date: June 18, 2004
Location: Minden , Nebraska
Posts: 1,277
I consider keeping track of case lot numbers to be a waste of time
steveno is offline  
Old January 23, 2005, 08:42 PM   #3
griz
Senior Member
 
Join Date: July 31, 2000
Location: Middle Peninsula, VA
Posts: 1,427
I try to keep rifle brass sorted, but mostly by keeping differnt batches separated. I have used a sharpie marker to code the primers, but of course that is only good until you deprime. You can use the sharpie on the case itself, but tumbling or solvents will wear it away after a short while. I've heard of people who file a small notch on the rim, and this could be a way to keep track of the nimber of firings on a single piece of brass. I've never tried that.

Pistol brass I pretty much just sort by headstamp, if that. The exception is max magnum loads, for which I use either once or twice fired brass.
griz is offline  
Old January 24, 2005, 11:40 AM   #4
Master Blaster
Senior Member
 
Join Date: October 11, 1999
Location: One of the original 13 Colonies
Posts: 2,027
I keep track of the number of firings on all of my many different calibers and generations of brass. Here is what I do.

When I get a new batch of once fired brass, I clean it in my tumbler, then I place it in large ziploc bags (2 Gallon heavy duty) I mark on the bag with masking tape, The date, 1X fired. when I load it for the second firing, I mark the date load and the number of loaded (2x) on a slip of paper in the box of relaoded rounds. I fire it and place the fired cases in a cut off gallon milk jug marked with the caliber and number of firings(2X). I then clean the brass again when the jug fills and mark, the plastic bag with the loading number 3X. And so on, its not hard to do. So I know how many firings on every piece of brass I have.

I load .223, 30.06, .308, 9mm, .38 spl, 357 mag, 44 mag, .45 acp, 32 acp, and I manage to keep track of it all. I toss the brass when a particular lot has a large number of splits (hasnt happened and some of my .45 has been loaded 15x). or shows signs of case seperation or loss of case neck tension due to work hardening in the case of rifle rounds. I buy once fired brass or new brass, from a local range in the case of pistol. My rifle is bought new, or given to me by those who dont reload, .223 and .308 I buy 1x fired 100 % processed lake city brass from scharchs(sp). Is ort the .223 and .308 by headstamp for accuracy reasons.

My procedure is not difficult or expensive, just requires masking tape, a marker, milk jugs, and plastic bags, and keeping things seperated.

I think it enhances safety, and quality of my reloads.
__________________
The difference between Democrats and Republicans is like the difference between a poop sandwich, and a poop Sandwich with mustard.
Master Blaster is offline  
Old January 24, 2005, 11:56 AM   #5
jerryd
Senior Member
 
Join Date: May 21, 2004
Location: Ct.
Posts: 114
Plastic zipper bags!!
jerryd is offline  
Old January 24, 2005, 01:03 PM   #6
30Cal
Senior Member
 
Join Date: December 3, 2002
Posts: 1,095
I color code the case heads using a sharpy on rifle brass to keep track of how many times it's been fired. Still, it's a PITA.
30Cal is offline  
Old January 24, 2005, 01:23 PM   #7
Robert M Boren Sr
Senior Member
 
Join Date: December 29, 2004
Location: NW Montana
Posts: 267
I feel it's a waste of time unless you're shooting compitition. Then I would just keep the brass seperated while I shoot it by keeping it in a container like a coffee can marked target. If it's just for normal stuff like hunting and plinking I feel it's just a waste of time.
Robert M Boren Sr is offline  
Old January 25, 2005, 08:56 PM   #8
HSMITH
Senior Member
 
Join Date: June 21, 2002
Posts: 2,019
You can take a file and put a notch in the rim, one notch for one lot, two notches for the next......
HSMITH is offline  
Old January 26, 2005, 12:18 PM   #9
Boudin
Junior Member
 
Join Date: December 14, 2004
Posts: 5
Thanks everybody, I have been filing small notches; it's a pain to do with a hundred cases, haven't found a way to color code that doesn't wear off as fast as you put it on.
Boudin is offline  
Old January 26, 2005, 02:01 PM   #10
Dave R
Senior Member
 
Join Date: January 7, 2000
Location: Idaho
Posts: 6,073
Most of my cases I don't track. 9mm, .308, etc. If the neck splits, I toss it.

But for my .17 wildcat, I'm more careful, partly because I want to see how many loadings I can get out of the brass.

So what I do is give each batch of brass its own cartridge box(es). Then, every time I load that brass, I mark the number of times loaded on the box. I'm up to 8 loadings on my most used batch.
__________________
I am Pro-Rights (on gun issues).
Dave R is offline  
Old January 26, 2005, 03:29 PM   #11
Tim R
Senior Member
 
Join Date: November 30, 2004
Location: God's side of Washington State
Posts: 1,601
Some I keep track of, some I don't. I don't keep track of 45 ACP as I use it until it wears out or is lost. I do keep head stamps as close to the same as I can. For other pistol calibers, I keep track by using the same ammo box ie, loaded ammo is pulled from the box, and the empties are placed back in the box when picked up. On the lid I use a avery label for load data and # times fired. Wheel guns make this easy.

For rifle, since I load so much of it, I use zip lock bags to store brass with a label or piece of paper telling me how many times fired. For the match rifle stuff, I put 125 cases into a "lot" and load a hundred at time saving the 25 in yet a smaller bag within the bigger bag. I use these 25 to replace lost cases I've shot. Brass monsters seem to like L/C match brass. After the cases have 4 reloads max on them they are pitched. If there is any of the 25 left over they go back in the mix as they are only once fired to start with. I have a fair amount of L/C match brass with same year manf. Hunting ammo is kept in 50 rounds lots and when fired the 50 ends up in a zip lock with details on a label or paper. I hang on to hunting rifle brass until the brass is done and number of reloads depends on the heat of the round. I also reload for a '06 M-1 and shoot it in John C. Garand matches. Sort of the same deal as the 308 ammo but I reload it intil there is a issue with the "Lot".
__________________
God Bless our Troops especially our Snipers.
Tim R is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:47 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08656 seconds with 7 queries