The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Hunt

Reply
 
Thread Tools
Old December 11, 2002, 02:26 PM   #1
NYCOP
Member
 
Join Date: October 23, 2002
Posts: 64
Moly coated bullets? are they worth it? For AR-15 varmit hunting

I am looking at the hornady 55 GR Vamx bullets, If I chosse these should I get the moly coated ones? or the non moly? they are the same price, should they hit pretty close to where my Q3131A winchester pratice ammo hits?
__________________
BUSHMASTER AR-15 A3 20 INCH H/BAR,
HANDLE MOUNTED COLT SCOPE 3/20.
NYCOP is offline  
Old December 12, 2002, 01:29 AM   #2
Freedom in theSkies
Senior Member
 
Join Date: October 7, 2001
Location: The "Nice Dictatorship" of Canada
Posts: 250
Personally I have found no validity in shooting Moly coated bullets. One negative point is that when the moly lifts off the bore, it can promote corrosion.
In the Air Force, we used to use it on throttle quadrants and carb linkages... They stopped using it for the same reason...

BTW, do you want to buy a moly plating kit...going cheap.
__________________
Live in peace... But defend it...Embrace it... But never take it for granted...
Freedom in theSkies is offline  
Old December 12, 2002, 03:11 AM   #3
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,576
For a clean kill, absent a head or neck shot, a .223 is about a 200-yard gun, no matter what bullet you use. The effectiveness on any game animal depends on enough speed for fragmentation inside the animal, and any .22 centerfire bullet loses velocity fairly rapidly.

Sure, an animal will die from a slowed-down bullet, but my own ethic sez "right now" is better than "sometime later".

, Art
__________________
You're from BATFE? Come right in! I use all your fine products!
Art Eatman is offline  
Old December 12, 2002, 09:41 AM   #4
dakotasin
Senior Member
 
Join Date: June 22, 2002
Location: south dakota, U.S.A.
Posts: 136
i'm a huge fan of the v-max's. i do quite a bit of prairie doggin', and the v-max is what i use in my small rifles (223, 22-250).

i don't know what caliber you are shooting, but by art's reply, it is 223. in that case, look for something a little lighter than the 55's. have had best success in 223 w/ 40-45 grain bullets.

the moly debate is still going strong. if you start w/ a clean bore, and shoot only moly, you'll probably notice a decrease in cleaning frequency. velocity increases may/may not happen...it takes more powder to achieve the same velocity as an uncoated bullet. i used to shoot a lot of moly, but have since switched back to uncoated bullets. the problem i had w/ moly was that when it was time to get a thorough cleaning, the stuff was near impossible to get out of the barrel.

as far as effective range of the 223 on varmints, i think that is a function of the varmint you are shooting at. i've no experience w/ woodchucks/groundhogs. lots of experience w/ prairie dogs. for me, the 223 has been an effective killer w/ v-max and ballistic tips out to around 400 yards, +/-. beyond that, the 223 is traveling so slow that the bullets lose their explosiveness. actually, real impressive explosions cease around 280 yards +/-, but on pd's you can get reliable kills a little further.

short answer to your question...i'd pass on the coated bullets. they function fine, but moly is kind of a hassle.
__________________
Hunting is not a matter of life or death. It is much more important than that.
dakotasin is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:41 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.05950 seconds with 7 queries