The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old December 10, 2002, 05:59 PM   #1
Skofnung
Member
 
Join Date: April 29, 2002
Location: Atlanta Area
Posts: 49
Ithaca 37 bolt removal

Hello again.

I have been searching the net for about 2 hours now trying to find a manual of how to take the reciever apart on my Ithaca 37 to give it a good scrubbing. I can't find anything.

I know I can get it apart, but being that it is an older design, I was wondering if there are any tricks to it, or if there are any things that I should look out for. Any suggestions? Any warnings?

Thanks for the help.
Skofnung is offline  
Old December 10, 2002, 06:19 PM   #2
ajacobs
Senior Member
 
Join Date: March 23, 2000
Posts: 210
I had the worst time when I got it, not being one to read manuals there should be a little silver round peice (like a wheel) that slides back and forth on a rod. You have to slide it oppisite of the spring tension to take the bolt out.

I am not looking at it right now and I am sure someone can phrase it better.
ajacobs is offline  
Old December 10, 2002, 08:03 PM   #3
Skofnung
Member
 
Join Date: April 29, 2002
Location: Atlanta Area
Posts: 49
I have removed every screw, and everything has come apart, except for the fact that the bolt will not come out of the reciever. Logic would dictate that the bolt has to go to the rear, but the pump bar (I forgot the true nomenclature(sp?) of the part) will not let it go back that far.

I have removed the front handguard for the first time, and I have noticed something strange. The pump bar is brazed to the tube that slides over the magazine tube. Is this normal? I got the gun used many moons ago, and it may not be normal.

Mr. ajacobs, where is this little round piece located? I looked and the only thing that looks like this is on the pump (forearm).

Thanks again
Skofnung is offline  
Old December 11, 2002, 04:42 AM   #4
Chuck Dye
Senior Member
 
Join Date: June 28, 2002
Location: Oregon-The wet side.
Posts: 878
First, see if you can find a March 2001 issue of The American Rifleman, which contains an exploded view and disassembly instructions.

Empty the gun and remove the barrel.

Remove the butt stock by removing the butt plate and using either a socket on a long extension or a large, long, flat bladed screwdriver. Remove the trigger plate screw, the unpaired screw on the left side of the receiver. Remove the carrier screw lock screws and carrier lock screws from each side of the receiver. Slide the trigger plate group out of the receiver. Turn the gun belly up with the magazine to the left. There is an hour glass shaped pin visible in the undersider of the slide: with a punch pull the pin toward your body until the slide bar can pulled forward from engagement with the slide. Pull the slide, breechblock, and carrier together rearward out of the receiver.

The top extractor is retained by a powerful spring. To remove it, use a thin punch to push the spring plunger back; at the same time push the extractor out of its seat. The bottom extractor can be removed easily by driving out its hinge pin. To remove the firing pin from the breechblock, first drive out the check pin. Then the firing pin and spring can be removed easily rearward. Reassembly is in reverse order.

My Featherlight was given to me. When I first stripped it down, it was likely the first time its was done in the 35 year life of the gun. The slide pin did not release the slide bar until it was fully drawn toward my body. May be close tolerances, may have been the large quantity of sludge involved. Persevere!

I strongly recommend obtaining the exploded view.
__________________
Gee, I'd love to see your data!
Chuck Dye is offline  
Old December 11, 2002, 07:59 AM   #5
Calanctus
Member
 
Join Date: April 7, 2002
Posts: 20
I'd check the Ithaca website: http://ithacagun.com
If you check under the support tab, there are pdf files of all the manuals you'd need to take it down. I've detail stripped mine, and didn't have any problems following their instructions.
Calanctus is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:36 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09158 seconds with 9 queries