The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old November 28, 2002, 12:59 PM   #1
Marshall
Senior Member
 
Join Date: August 27, 2001
Location: I live in a small bush community in southeast Alaska called Gustavus
Posts: 103
Target load for the .44mag using 240gr jacketed bullets?

I just put a Millet red dot sight on my S&W 629 Classic. I would like to load up some mild, accurate target loads for recreational shooting. I only have W-296 powder and 240gr Winchester jacketed bullets.

Any help would be appreciated.

Thanks.
__________________
marshall
Marshall is offline  
Old November 28, 2002, 02:08 PM   #2
Rick R
Senior Member
 
Join Date: April 1, 2002
Location: On top of a mountain in WV
Posts: 102
W296 does weird things if you load it too lightly, I use Unique for light to medium loads and 296 for serious stuff.
Rick R is offline  
Old November 28, 2002, 03:31 PM   #3
MADISON
Senior Member
 
Join Date: January 1, 2000
Location: Roanoke, Virginia
Posts: 2,678
Target load for the .44mag using 240gr

Target load for the .44mag using 240gr:
8.0 grains of UNIQUE
17.5 grains of 2400
5.0 grains of UNIQUE
MADISON is offline  
Old November 28, 2002, 09:20 PM   #4
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,316
No. 1 - Buy a reloading manual
No. 2 - Use any of the .44 Special loads

Jim
__________________
Jim K
James K is offline  
Old November 28, 2002, 10:47 PM   #5
Hal
Senior Member
 
Join Date: October 9, 1998
Location: Ohio USA
Posts: 7,435
I'll second , third and fourth all of the above.
Approx. 15 to 17 gr of 2400 makes a very pleasant target load w/jacketed or hard cast lead 240 gr bullets.
Hal is offline  
Old November 29, 2002, 10:52 PM   #6
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,316
I always recommend loading manuals. Any reloader needs one, or more. Just as a matter of principle, and because of an almost unfortunate situation, I don't give out any reloading info by phone or on the web. Too much chance of an error on my part or a misunderstanding on the part of the reader.

I once suggested to a friend over the phone that a load of x.y grains of Z powder in .38 Special was a mild target load. In reviewing his notes, my friend missed the decimal point. Thank goodness he called again and mentioned his loads of xy grains; I straightened him out, but whew!

Jim
__________________
Jim K
James K is offline  
Old November 30, 2002, 01:44 AM   #7
jtduncan
Senior Member
 
Join Date: December 5, 1999
Location: Seattle, Washington, USA
Posts: 1,681
7.3 grains of Universal and a 240 grain LSWC shoots some mighty fine holes out to 50 yards with my Redhawk!

I lightly roll crimp into the cannelure for a consistent burn too. But a light taper crimp may work as well.
__________________
The Seattle SharpShooter - TFL/GT/AR15/SGT/PCT/KTOG/SWF/RF/HKPRO/OA2/1911Forum
Reloaded .223 Rem, 9mm, 40SW, 357 SIG, 10mm, 44 Spl, 44 Mag, 45 ACP Today?
jtduncan is offline  
Old November 30, 2002, 12:45 PM   #8
Archie
Senior Member
 
Join Date: May 26, 2000
Location: Hastings, Nebrasksa - the Heartland!
Posts: 2,091
44 Magnum is a very accurate round in most any configuration.

However, you mentioned "...mild, accurate target loads..." and WW 296.

296 is a top end full power powder. Check out most any loading manual (Jim Keenan's right, you need a couple) and it will show you that even a light load of 296 is a high end load.

Unique is a good midrange powder. There are others. If you load for other calibers (or will), another can of powder is a fact of life.

But start with the loading books. I recommend Lyman and Speer and Hornady and Hodgdon. Perhaps not in that order.
__________________
There ain't no free lunch, except Jesus.
Archie

Check out updated journal at http://oldmanmontgomery.wordpress.com/
Archie is offline  
Old November 30, 2002, 11:28 PM   #9
C.R.Sam
Senior Member
 
Join Date: October 29, 1999
Location: Dewey, AZ
Posts: 12,859
Like Jim Keenan said...
Get book.
Better yet, get two books.
Read em cover to cover.

Sam
C.R.Sam is offline  
Old December 1, 2002, 07:32 PM   #10
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,213
COINCIDENCE? I THINK NOT.

7.3g Universal Clays under a 240g LSWC makes some serious groups (IPSC, you know) from my Redhawk, too.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old December 4, 2002, 10:46 AM   #11
sundog
Senior Member
 
Join Date: November 22, 1999
Location: Green Country, OK
Posts: 730
Green Dot (Green Dot? Yes, Green Dot!) makes very fine cast bullet loads. Check a Alliant and Lyman manuals for loads. sundog
__________________
safety first
sundog is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:39 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07984 seconds with 7 queries