The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old August 13, 2002, 08:53 AM   #1
branrot
Senior Member
 
Join Date: October 11, 1999
Location: Miami Beach, FL, USA
Posts: 1,367
P7M13 Question

My P7M13 has been jamming lately. After about 30 rounds, the slide starts to get stiff, and eventually it won't even open fully. I've been shooting reloads (my reloads; Hodgdon HP-38 powder), and am concerned that maybe some powder is getting into the gas system (the guy at the range told me the P7 didn't have a gas system... it has a gas system, right?). Is my speculation that the problem is with the ammo correct?

Yes, I know I should clean the gun (already did), and try it with factory ammo (have the ammo at home), but I'm not going to be at the range for at least 2 weeks (going out of town this weekend). Thanks for your help.
branrot is offline  
Old August 13, 2002, 11:55 AM   #2
sricciardelli
Senior Member
 
Join Date: August 13, 2001
Location: Montana
Posts: 489
The P7M13 has a gas retarded inertia bolt...

If the factory ammo shoots okay, use a cleaner powder in your reloads...but I doubt it is the gas system causing the problem, since you stated that the slide is getting gunky...
__________________
http://stevespages.com/page8.htm
sricciardelli is offline  
Old August 13, 2002, 06:20 PM   #3
Johnny Guest
Moderator Emeritus
 
Join Date: August 28, 1999
Location: North Texas
Posts: 4,116
Hey, branrot- - -

You said you'd been shooting reloads. You haven't been shooting lead bullet loads in your P7, have you? I have no personal experience with lead bullets in this pistol, but I've heard time and again that they really foul up the works.

Suggest you gp back over it and make certain that all fouling and lead residue is gone, and then try the jacketed ammo. The aluminum case Blazer ammo is available here about as cheap as I can handload 9 mm ammo. If you don't find this is the case, try purchasing 115 gr FMJ bullets in bulk and loading with about 5.5 of H. Univeral. Economical and clean.

That's a nice pistol, and I hope you can get it to working properly.

Best,
Johnny Guest
__________________
MOLON LABE!
Amendment II ensures the rest of the Bill of Rights.

Blog: Expert Witness
Johnny Guest is offline  
Old August 14, 2002, 02:04 PM   #4
branrot
Senior Member
 
Join Date: October 11, 1999
Location: Miami Beach, FL, USA
Posts: 1,367
No, my reloads are jacketed. West Coast Bullets. I'm going to give the factory loads a shot next time I go to the range.
branrot is offline  
Old August 14, 2002, 04:55 PM   #5
larryw
Senior Member
 
Join Date: January 17, 2002
Posts: 336
I've seen that happen on a friend's PSP as well. Dirty ammo, blamed on a bad batch of power by the manufacturer, was gumming up the gas piston. As the piston is attached to the slide, this was making it very difficult to rack. Further complicating the issue, once the gun cooled, the slide was 'glued' shut; he got it open and sent it to HK to make sure nothing was damaged.

P7 is a great gun, but in my opinion, the gas system is its Achilles Heel.
larryw is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:33 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06598 seconds with 7 queries