The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 22, 2002, 10:30 PM   #1
posigian
Senior Member
 
Join Date: May 31, 2000
Location: Great Lakes State
Posts: 115
Roll or Taper Crimp 44mag

What is the prefered method of crimping 44mag for my Super Redhawk?

If I get a set of RCBS Dies, how do I know if the crimp die is roll or taper crimp?

I need to know before I go to the store on Friday and would appreciate the help!

Posigian
posigian is offline  
Old May 22, 2002, 10:39 PM   #2
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,483
A roll crimp is the preferred crimp for a .44 Magnum/Special. On the box label it will have "TC" along with the cartridge designation if it is a taper crimp die set. If it is roll crimp it will have only the cartridge designation, i.e., it won't have "RC" or the like. And to be on the safe side, I would open the box and check the top of the crimping die. It will say whether it is roll or taper.

In reality, you could probably take a .44 Mag die set blindfolded since the store would most likely have to special order a taper crimp die set. So the odds are many to 1 that you will have only that one choice anyway.
Mal H is offline  
Old May 22, 2002, 10:41 PM   #3
Archie
Senior Member
 
Join Date: May 26, 2000
Location: Hastings, Nebrasksa - the Heartland!
Posts: 2,083
For the full loads, anyway....

Roll crimp the snot out of it!!!

Heavy crimp does two important things:
Helps the powder to burn properly, and
Keeps bullets from pulling out of the cases. In a revolver, heavy recoil acts just like a kinetic bullet puller.

Most factory dies for revolvers are designed to roll crimp. It's a pretty safe bet that standard RCBS dies are roll crimpers.
I would recomend the Lee Factory Crimp die. It's what I use on my 44 Magnum. And dang near everything else, too.
__________________
There ain't no free lunch, except Jesus.
Archie

Check out updated journal at http://oldmanmontgomery.wordpress.com/
Archie is offline  
Old May 23, 2002, 12:47 AM   #4
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 35,754
Taper crimp may hold you up through medium-power loads.

After that, you'll need increasing amounts of roll crimp as the power levels go up.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old May 23, 2002, 04:32 AM   #5
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,139
PROFESSIONAL-GRADE ADVICE

Best: Redding Profile Crimp die; will enhance accuracy and consistency. Apply 'heavy' crimp to 'heavy' loads; apply 'medium-heavy' crimp to all other loads.

Your results will not vary.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old May 24, 2002, 10:27 AM   #6
MADISON
Senior Member
 
Join Date: January 1, 2000
Location: Roanoke, Virginia
Posts: 2,678
Roll or Taper Crimp 44mag

I use a TAPER CRIMP, which is nothing more than the sizer die without the decapping stem, on all my handguns.
If you trim your handgun/44 cases then a roll crimp will woork well. I DO NOT TRIM my handgun cases and with a taper crimp, it doesn't matter.
MADISON is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:09 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07824 seconds with 7 queries