The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

View Poll Results: Do you ream your rifle case`s necks?
ream all cases 2 13.33%
ream after trimming only 4 26.67%
ream when I feel anthusiastic 0 0%
Dont ream at all 9 60.00%
Voters: 15. You may not vote on this poll

Reply
 
Thread Tools
Old May 17, 2002, 08:20 PM   #1
Fatelvis
Senior Member
 
Join Date: June 10, 2001
Location: Lockport, IL
Posts: 488
Do you ream your necks?

Do you ream your rifle case necks? (Inside and Outside?)
Fatelvis is offline  
Old May 17, 2002, 08:57 PM   #2
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,416
I've always started with factory brass, for my serious shooting--which is mostly load development, sighting in, and then hunting. I've never had any sort of problem which led me to believe it was necessary.

Were I competing in benchrest or long-range military, etc., it might well be different. Maximum uniformity is more important, there.

Art
__________________
You're from BATFE? Come right in! I use all your fine products!
Art Eatman is offline  
Old May 18, 2002, 12:58 AM   #3
Archie
Senior Member
 
Join Date: May 26, 2000
Location: Hastings, Nebrasksa - the Heartland!
Posts: 2,087
I outside neck turn ....

for my .22-250 and the .308 bolt gun.

For my high power rifle and hunting loads, I check things, but don't trim or turn unless I'm out of specification.
__________________
There ain't no free lunch, except Jesus.
Archie

Check out updated journal at http://oldmanmontgomery.wordpress.com/
Archie is offline  
Old May 18, 2002, 05:09 PM   #4
labgrade
Member In Memoriam
 
Join Date: November 29, 1999
Location: west of a small town, CO
Posts: 4,346
Never yet - although I might if (when) I ever get a couple rifles rebarreled - just to run an experiment with 50 cases done "as usual" and another 50 all weighed for case capacity/reamed, etc. - the whole drill.

If a 30+ year-old rifle with 20K+ rounds through it will still shoot sub-1/4MOA, I would really! like to see the diffference tweaking the cases'll do.

I may actually give a hoot enough to try to wring out the best accuracy ....
labgrade is offline  
Old May 18, 2002, 10:02 PM   #5
Steve Smith
Senior Member
 
Join Date: December 9, 1999
Posts: 4,131
Not for my match rifle. Of course, I shoot HP, where position will count for much more than a reamed neck. In addition, a military rifle, even with the Wylde or equivalent chamber will have enough room so that the necks are not nearly as important as with a bolt gun. I focus on things that will provide a tangible improvement. Now Benchresters will much more likely to be doing this. I just square up primer pockets, deburr flash holes, chamfer and deburr necks.
__________________
Favor the X.


Steve Smith
NRA Life Member
Steve Smith is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:43 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06499 seconds with 8 queries