The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Art of the Rifle: Semi-automatics

Reply
 
Thread Tools
Old February 19, 2012, 10:07 AM   #26
BPowderkeg
Junior member
 
Join Date: September 27, 2011
Posts: 382
i too have one of those Rem. M-24, S/N XXXX, i got it and 9 other guns that were stacked in a corner of a "trailer home" that caught fire, i bought those guns from a friend who lost his father in the fire.

the forearm was a little scorched (?) it was a well used little rifle, the problem it has is that the extractor falls out after several shots, that little doodad plunger (?) that keeps the extractor in place is worn, if anyone has a schematic please post it or the URL to it, i liked shooting it but can not due to that part falling out.., can anyone help me get this rifle back into shooting condition ?

thank you.

I FOUND IT !!!

http://www.wisnersinc.com/additional...mington_24.htm

Last edited by BPowderkeg; February 19, 2012 at 10:33 AM. Reason: I FOUND IT !!!
BPowderkeg is offline  
Old April 3, 2012, 08:09 PM   #27
boitanosr
Junior Member
 
Join Date: April 3, 2012
Location: sutter creek, calif.
Posts: 2
pops

were you able to keep the extractor in place? i am having the same problem.
boitanosr is offline  
Old June 17, 2012, 07:10 AM   #28
Beechdrvr
Junior Member
 
Join Date: June 17, 2012
Posts: 3
Front site on Model 24 Short

Hi Guys,

I have a 1929 Model 24 short in excellent condition which I just inherited. I took it to the range to site it in. Shot nice but, Im having doubts that the front site is original.
Is there anyone who could measure their front site from the barrel to the white pipper and give me a reading?
Would really appreciate it.
Thanks
Beechdrvr is offline  
Old September 20, 2012, 03:58 PM   #29
OldShot
Junior Member
 
Join Date: August 20, 2012
Posts: 5
Model 24 Issues

Picked up a Remington Model 24, serial number 399xx, at a gun show last weekend, took it to the local gunsmith for a good cleaning and oiling and got it back today. After about 25 rounds of CCI Standard Velocity the barrel was loose from the receiver. The locking tab was forward out of the slot in the receiver. Should there be a spring behind that tab to keep it engaged?

Now that the rifle is cool the barrel is tighter but still wiggles slightly. Just how tight should it be?

I also had five or six fail to eject. Before giving it to the smith I had run 25 rounds through it with no FTE. Does the rifle just need some more tweaking or is it worn out?
OldShot is offline  
Old January 3, 2013, 07:28 PM   #30
PaulN
Junior Member
 
Join Date: January 25, 2012
Location: north of Dallas (Tx)
Posts: 3
Comments re> Take-Down Barrel Tightness

The Remington Model 24, and Model 241, take-down .22 rifles should have their barrels adjusted just tight enough such that they don't have perceptable wobble under normal handling.

When reattaching the barrel the force required to rotate it should significantly increase just as the barrel is coming to its correct (attached) orientation.

A gunsmith told me, as I was picking-up a Model 241 from being cleaned, that he felt that it was better to leave any take-down rifle in its attached state except for when it was really necessary to break it down for travel. He said that every time a take-down rifle has its barrel removed-and-reattached that it contributes to wear (I already thought that but apparently the gunsmith felt the amount of wear was above-and-beyond what would be considered as 'normal wear').

(I'll add this comment ..... Although I think that the Remington Models 24 and 241 ... and the Browning SA-22 .... are beautiful .22 rifles but they can be tough to clean up inside their receivers after doing some plinking. I use Q-Tips, soaked in CLP, to run around in the receiver next to the breech; it's surprising how much burned powder accumulates there.)
PaulN is offline  
Old April 25, 2014, 12:23 AM   #31
dblwizard
Junior Member
 
Join Date: April 24, 2014
Posts: 1
Howdy, I have a buddy that has one of these and is looking for a fore stock. Anybody have any idea's of where we could find one? Looking for an actual Remington stock rather than a replica. Any help would be greatly appreciated.

Thanks

dbl
dblwizard is offline  
Old April 26, 2014, 11:25 AM   #32
ole-crabby
Junior Member
 
Join Date: September 15, 2010
Location: asheville NC
Posts: 6
model 24 remington

reply to a old thread I also own a model 24 ser. 51xxx mine has a empty shell deflector on the bottom have never seen another one. your question go to macon gunstocks .com and do a search, they have plain or really fancy stocks pricey but pretty!
ole-crabby is offline  
Old July 8, 2014, 12:55 PM   #33
Taylors7558
Junior Member
 
Join Date: July 7, 2014
Posts: 1
Hi Everyone, I'm new here. I just inherited a Model 24 (.22 Short) from my grandfather. It was originally my great grand fathers, and I was hoping to find out how to go about finding the "grade" of it, as I noticed it was made in a few different grades. Is there anyone on the forums that would be able to give me such information? Also, I noticed that every one I've seen has the serial stamped on the side of the receiver, and mine is completely blank. Mine only has the serial stamped on the front of the receiver (have to break it down to see it).

Serial is 25566.

Thanks to anyone who can help me get information on this neat little rifle!
Taylors7558 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:01 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08461 seconds with 7 queries