The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old February 7, 2002, 01:40 PM   #1
MLC
Senior Member
 
Join Date: October 9, 2001
Location: New Hope, PA
Posts: 230
tips for ejector removal in walther PPK

This pistol has been abused!
It is utterly filthy and has tattered remnants of
the ejector spring still inside. Is there any sort of trick not coverd in the manual for removal of this little fella?
MLC is offline  
Old February 7, 2002, 10:15 PM   #2
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 6,836
To remove the ejector, insert a small, very thin bladed screwdriver under the ejector spring to help force the spring up inside the ejector. Wiggle the ejector up and out of it's recess.
Dfariswheel is offline  
Old February 7, 2002, 10:39 PM   #3
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,858
Hi, guys,

Dfariswheel, I think you are holding the gun upside down to work on it, like many people do. But to avoid confusion, when the gun is held normally, the spring is on the top of the ejector and is pushed down to get it out of the groove in the frame so the ejector can be removed. BTW, the ejector also acts as the slide stop, which is why it needs a spring in the first place.

Jim
__________________
Jim K
James K is offline  
Old February 8, 2002, 02:38 AM   #4
Dfariswheel
Senior Member
 
Join Date: May 4, 2001
Posts: 6,836
Jim: How the hell did you know?......
I would have remembered that, except I sold my last PP series a few years ago, and didn't bother checking the exploded view.
Besides the sun got in my eyes.
Dfariswheel is offline  
Old February 10, 2002, 11:17 PM   #5
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,858
Hi, guys,

Not magic. I got out a PPK and checked to be sure.

Jim
__________________
Jim K
James K is offline  
Old February 10, 2002, 11:33 PM   #6
MLC
Senior Member
 
Join Date: October 9, 2001
Location: New Hope, PA
Posts: 230
Fellas I have to admit that I am utterly retarded. I intended to ask about the removal of the loaded chamber indicator spring.
Whoops!! again retarded. Removal of the ejector spring would probably take an educated sea monkey less than 5 minutes.
MLC is offline  
Old February 12, 2002, 09:33 PM   #7
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,858
HKLVR, that is a whole nutter ball game. Do you really HAVE to, or do you want to tear everything apart for the fun of it? That is not a part normally removed for cleaning and a good spray cleaner should work fine.

IF you insist, read the following at least twice before doing anything, and get a place to work that is clear of junk.

Place the safety in the off (up) position and remove the slide from the frame. Turn the slide upside down. Using a punch or small screwdriver push forward on the little shelf on the firing pin until the firing pin clears the safety. (The firing pin will stick out about 1/2 inch from the breech face.) Hold it there (needle nose pliers will work) and turn the safety to a position midway between the off and on positions.

Insert a small screwdriver in one of the slots in the safety and push it to the right (as normally thought of) but anyway toward the thumbpiece side. NOTE NOTE. When the safety comes out, the firing pin and spring will take off if you let them. Let the firing pin back easy, and out of the slide. Also the safety detent plunger and spring will pop out of the slide into the hole where the safety was. Leave them alone, they won't fly.

Now, look down into the slide below where the firing pin was and you will see the loaded indicator and its spring. There is a hole in the indicator. Insert the punch into that hole and pull back and up. The indicator and spring will come up and can be eased out to the front. AGAIN NOTE. These parts can also fly away.

Reassemble in reverse order. Use a small screwdriver to push the safety plunger into the slide so you can get the safety in.

If you can do this without losing any parts, congratulations!

HTH

Jim
__________________
Jim K
James K is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:27 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06886 seconds with 7 queries