|
Forum Rules | Firearms Safety | Firearms Photos | Links | Library | Lost Password | Email Changes |
Register | FAQ | Calendar | Today's Posts | Search |
|
Thread Tools | Search this Thread |
March 2, 2013, 12:02 PM | #1 |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
Shotgun cartridge potency. Increased over the decades?
I am planning to try out my two shotguns tomorrow. They both belonged to my Grandad and they pretty old (50-60 years old). One is a 16g single shot, the other a 12g semi.
Of the two, I can see myself shooting the 12g more and so my question is largely regarding this one. I have bought some 12g birdshot cartridges (shot weight is 34grams of 0/0 by Nobel Sport). I basically want to see if it cycles correctly. However, in general, will the powder charges and projectile weights have changed massively since these were produced? In other words, is there some kind of potency level I should stay below in order to not run the risk of damaging this little piece of family history? If so what is the way of identifying this level? My guess is that ammo has increased in power thanks to improvements in metal grades and strength of the guns produced. Thanks.
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
|
March 2, 2013, 01:19 PM | #2 |
Senior Member
Join Date: February 3, 2013
Posts: 1,235
|
For openers, you say that you have some birdshot cartridges loaded with 34 grams of 0/0. I am not sure what you have, but it sounds like you have some 00 (double ought) buckshot.
The 34 grams is probably the weight of the powder. Different powders can have more or less energy per gram, which is why equvalent loads may have more or less powder depending. I rarely use buck and am not sure, but 34 grams seems to be a tad on the heavy side. What is your 12 gauge chambered to use; 2-3/4 or 3" shot shells? Be careful. 3 may fit a 2-3/4 chamber, but not when the petals of the shell unfold. Firing a 3 in a gun designed for 2-3/4 can result in dangerously high barrel pressures. Shot shell boxes should be marked with equivalents, which tells you the powder's equivalence to an old black powder load. I don't believe that total projectile weights have changed that much, but depending on the use you may need more boom boom to accomplish the same mission. Often regulations require steel shot and I undrstand, but may be totally wrong, that becasuse steel shot is less dense more muzzle energy is needed for some purposes, like hitting high flying fowl. This may help. http://en.wikipedia.org/wiki/Shotgun_shell You may want to post the make and model of your gun and specify that shotshell. Last edited by Dreaming100Straight; March 2, 2013 at 01:29 PM. |
March 2, 2013, 02:07 PM | #3 |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
I've had a quick look online, and the shotgun (A Verney Carron Luigi Franchi Automatic) is 12/70, so that means I need 2 3/4 inch cartridges....
I've checked and my cartridges are 70mm, so OK on the cartridge length front. Here is a link to the cartridge manufacturer. It should land you on page 4 of the 12g results list. Just scroll down to the green Nobel Speed. I did not ask for super light loads as I read somewhere that this model needs some punch to cycle properly, but if I've been sold some ridiculous over-kill nuclear magnum loads, tell me now, as I don't want to reduce my Grandad's gun to pieces!!! The 16g is a single shot Beretta from the '50s... I got these for that one: SMI standard. It is the only result when searching under 16g... Presumably if I slide the cartridge into the chamber and it fits, flush with the face, it should be OK, no? Again if you feel that is too much boom-boom for a 60 year old shotgun, please tell me!!
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
|
March 2, 2013, 04:20 PM | #4 | |
Senior Member
Join Date: May 7, 2012
Location: Sweden
Posts: 1,000
|
Quote:
loads of older guns are 65mm, and 70mm shells fit into those so be aware. prolly not blow up the gun but it is not made for those. it should read the kind you need on the barrel |
|
March 2, 2013, 04:24 PM | #5 |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
Nothing that I can see on the barrel, apart from "16".
What if I measure the depth of the chamber with a caliper? For it to take a 70mm cartridge do I need greater length in the chamber? At the moment, it measures 70mm down to a sloped lip in the barrel. It is not a stepped edge, but rather a throat, like in the cylinder of a revolver. The Beretta is a Model 412, 16 cal if that helps... So. Can anyone advise on the suitability of the cartridges I've bought? Good to go? (Goodness!! Why can't a 12 just be a 12 and a 16 be a 16....)
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
Last edited by Pond, James Pond; March 2, 2013 at 04:40 PM. |
March 2, 2013, 04:26 PM | #6 | |
Junior member
Join Date: December 20, 2012
Location: The "Gunshine State"
Posts: 1,981
|
I SERIOUSLY doubt that 34 GRAMS is the powder charge as opposed to the shot charge. Even 34 GRAINS would be a whale of a charge
34 GRAMS is a 1-1/8oz load Shotgun hull length is the FIRED length. 70 is 2-3/4, 65 is 2-1/2, 60 is 2" Quote:
|
|
March 2, 2013, 04:29 PM | #7 |
Senior Member
Join Date: February 3, 2013
Posts: 1,235
|
i don't know the answer. You indeed have 2-3/4 inchers, but I do not know if that model or your barrel is rated for a magnum load. This reminds me of when I was sold magnums for a 12 gauge manufactured in 1908 and I showed the idiot at the gun store the old single shot. I knew nothing about shotguns, then and, fortunately, I never shot it. I would not shoot them in your's until you have the answer.
|
March 2, 2013, 04:35 PM | #8 | |
Senior Member
Join Date: May 7, 2012
Location: Sweden
Posts: 1,000
|
Quote:
shooting 70mm in a 65mm gun can cause higher gas pressures and whatnot, the most likely thing that will happen is that yo won't get the spread/coverage you wold excpect, but I can't recommend it. the least that will happen is that you will shot your gun loose de to the higher gas pressure it will be hard to measure because the chamber gradually cones out into the barrel. |
|
March 2, 2013, 04:47 PM | #9 | ||
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
Seems I got 3 answers as I was editing my last post...
Quote:
If they are not, then it should be OK in my gun, no? Quote:
This is turning into a right puzzle...
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
Last edited by Pond, James Pond; March 2, 2013 at 04:55 PM. |
||
March 2, 2013, 04:52 PM | #10 |
Senior Member
Join Date: May 7, 2012
Location: Sweden
Posts: 1,000
|
take the gun apart, it might be stamped under the forearm
|
March 2, 2013, 04:56 PM | #11 | |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
Quote:
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
|
|
March 2, 2013, 04:59 PM | #12 | |
Senior Member
Join Date: May 7, 2012
Location: Sweden
Posts: 1,000
|
Quote:
28-32 should be fine ammo should be labeled with a US nr, that is the standard, us7, 8, or 9 is practise ammo and perhaps for some smallish birds, it is the size(and number of) pellets, the higher the nr the smaller pellets above 32 is when they start using terms like express, magnum and so on. if the gun is really old you should look for proofmarks http://www.shotguns.se/html/italy.html well your edit suited my link greatly, finito so we know it is for smokeless powder atleast I would recommend e-mailing the guy behind that site if you have further questions, he is an expert on shotguns, even recently wrote a book, I am sre he could help you |
|
March 2, 2013, 05:00 PM | #13 | |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
Quote:
This was written under the forearm. Does this tell you anything? What looks like "K", followed by 0.775. Then there is 18.6 stamped above 70 (presumably the hull length). Finally there is 16.5, written over 17.1. Make any sense?
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
|
|
March 2, 2013, 05:04 PM | #14 |
Senior Member
Join Date: May 7, 2012
Location: Sweden
Posts: 1,000
|
|
March 2, 2013, 05:05 PM | #15 | |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
Quote:
The VC 12g is more recent, probably from the 60's. I'll see what I can see on it. I'll also have a look for any number codes for the ammo, although all the information should be on the link I post earlier... Hopefully, this will lead to the answers, and these guns can be shot for the first time in about 30 years!!
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
|
|
March 2, 2013, 05:08 PM | #16 |
Senior Member
Join Date: May 7, 2012
Location: Sweden
Posts: 1,000
|
and not knowing anything about the semi...
there is probably an O-ring that will need replacing, maybe a magazine spring that is rusted to bits aswell, after 30 years of not being used. you will probalby need to "experiment" in how it will need to be oiled to cycle properly, some guns wants to be drenched, some just a dash on certain parts and so on. |
March 2, 2013, 05:34 PM | #17 |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
On the semi, everything moves very freely and there was no sign of rust on either of them. Testimony to my Dad's excellent storage duringhis stewardship!!
Anyway the VC only seems to have a crossed swords stamp, with "PT" beneath them. That is it... Husqvarna: Thanks for all the input so far. Hopefully, I can work things out by tomorrow. The cartridge sizes are OK, and if these are middling to low-end loads, I think all will be OK. A bit more research on the Nobel Sport cartridges for now, I think!!
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
Last edited by Pond, James Pond; March 2, 2013 at 05:42 PM. |
March 2, 2013, 06:01 PM | #18 |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
Update:
I've found the stamp for the Verney Carron. The stamp is two crowns set above "PT", and with a sort of lightning bolt motif below that and translates as "Standard final smokeless re-enforced proof 15646 psi" The stamps for the Beretta tell me a little less: There I've only found that the gun is good for smokeless powder. Great link, there, Husqvarna!! The Nobel Sport cartridges are classed as "Traditional 12G" and "Tradintional 20-16". I don't think these are firebreathers. It should be OK.
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
|
March 2, 2013, 07:07 PM | #19 |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
FWIW, The last significant power change to shotshell ammo, other than elongation ( to 3" or 3-1/2" shells ) was in 1926.
AFAIK, Both of your shotguns should have 2-3/4" (70mm) chambers. "16.5" & "17.1" are bore measurements, indicating the amount of constriction, i.e., choke. Your Beretta 412 was known as the Folding Companion - the loads shot through it should take it's light weight into consideration. Your Verney Carron Luigi Franchi Automatic is a clone of the Franchi AL-48, a long-recoil autoloader - and while it's safe with all 2-3/4" loads, the bevel on the friction ring around the mag tube, just ahead of the recoil spring (under the forend wood) MUST face in opposite directions for heavy (magnum) or light loads - or - shooting heavy loads with the bevel in the "light load" position will damage the forend and maybe the receiver; shooting light loads with the bevel in the "heavy loads" position may cause misfeeds. . Last edited by PetahW; March 2, 2013 at 07:26 PM. |
March 3, 2013, 12:49 AM | #20 |
Staff
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 41,390
|
"The 34 grams is probably the weight of the powder."
Uhm... I'd say it shouldn't be. 34 GRAMS of powder would be a bit over 524 GRAINS of powder. 34 GRAMS of shot, however, is just shy of 1 and 1/4 ounces.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza Baby Jesus cries when the fat redneck doesn't have military-grade firepower. |
March 3, 2013, 02:20 AM | #21 |
Senior Member
Join Date: February 3, 2013
Posts: 1,235
|
Mike is correct. I was thinking grains of powder.
|
March 3, 2013, 03:44 AM | #22 |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
Wow, guys. What a great set of posts!! (As always...)
PetahW: great stuff! Where did you find all that information?! I will look at the VC bevel to see if it is clear which way round is which. I don't think mine are heavy loads, based on the information on the manufacturer's website. If I have any doubts, I will postpone my test, but so far, so good.
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
|
March 3, 2013, 11:15 AM | #23 |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
I've owned/shot/hunted with both a Beretta Companion (12ga, though), and 3-4 different AL-48's (standard & magnum models).
As for setting the friction ring: If you look at the brass ring, it has a steel ring on the outside that holds it tight. As this slides on the mag tube, it hits the spring. The bevel ring on top of the spring can be flipped for light or heavy loads. If the bevel is towards the brass ring, it's for heavy loads - as the ring is pushed back by the barrel, the beveled ring will compress it making is grip the mag tube more tightly. Conversely, for light loads, if you flip the ring so the flat side is against the brass ring, it just slides and does not compress. . Last edited by PetahW; March 3, 2013 at 11:29 AM. |
March 3, 2013, 03:35 PM | #24 |
Senior Member
Join Date: July 12, 2011
Location: Top of the Baltic stack
Posts: 6,079
|
I decided not to shoot anything today: still a few questions to check.
PetahW: Thanks for the description, but my lak of knowledge of part names has let me down. I took a picture of my internals, spreading them out along the magazine tube to be more clearly visible. Looking at the brass ring, with the black steel ring over it, I can see more brass on the side of the bevel, and less on the side of the spring. To my mind this means that the gun is configured for standard lighter loads at present. Do you agree? Does the mag-tube where this ring sits need to be lubed? At the moment it is dry. Secondly, do you feel that a 28 grain charge in my 16 cartridges is too much for the little Beretta? I hope not, as it is the only one made by that company so I imagine it is not particularly powerful... Thanks!!
__________________
When the right to effective self-defence is denied, that right to self-defence which remains is essentially symbolic. Freedom: Please enjoy responsibly.
|
March 3, 2013, 07:59 PM | #25 |
Senior Member
Join Date: September 19, 2008
Posts: 4,678
|
Your auto appears to be setup for heavy loads, as it looks to me like the bevel inside the governor ring (between the bronze friction ring and the recoil spring) is facing the beveled surface of the friction ring.
For light loads, the governor ring's opposite/flat surface should be against the bronze friction ring. The magazine tube requires light lubrication for proper operation (gun oil). Since I'm unfamiliar with the brand, I cannot comment on the shotshell load for your Beretta, other than to say the gun's certified for any commercial ammo - but may beat your shoulder to death with heavy loads, even though the gun itself may be able to handle same. You'll certainly find out, the first time you pull the trigger on one. . |
|
|